B1602/83 Lost Communication with Front Satellite Sensor Bus RH
Diagnostic trouble codes · Vehicles built from Jan 2007
Also covers:
- B1603/83 Front Satellite Sensor Bus RH Initialization Incomplete
- B1612/83 Lost Communication with Front Airbag Sensor RH
- B1613/83 Front Airbag Sensor RH Initialization Incomplete
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
DESCRIPTION
The front airbag sensor RH consists of the diagnostic circuit and the frontal deceleration sensor.If the center airbag sensor receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1602/83, B1603/83, B1612/83 or B1613/83 is recorded when a malfunction is detected in the front airbag sensor RH circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1602/83 B1603/83 B1612/83 B1613/83 |
When one of following conditions is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor RH.
- OK:
- The connectors are connected.
|
|
||||
| OK | |
| 2. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN) |
![]() ![]() |
Disconnect the connectors from the center airbag sensor and the front airbag sensor RH.
Using a service wire, connect A45-2 (+SR) and A45-1 (-SR) of connector E.
- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E49-29 (+SR) - E49-27 (-SR)
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT) |
![]() ![]() |
Disconnect the service wire from connector E.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E49-29 (+SR) - E49-27 (-SR)
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO B+) |
![]() ![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
E49-29 (+SR) - Body ground
Below 1 V
E49-27 (-SR) - Body ground
Below 1 V
|
|
||||
| OK | |
| 5. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO GROUND) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E49-29 (+SR) - Body ground
1 MΩ or higher
E49-27 (-SR) - Body ground
1 MΩ or higher
|
|
||||
| OK | |
| 6. CHECK FRONT AIRBAG SENSOR RH |
![]() ![]() |
Connect the connectors to the center airbag sensor.
Interchange the front airbag sensor RH and LH, and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
Result Result
Proceed to
DTC B1602/83, B1603/83, B1612/83, B1613/83, B1607/84, B1608/84, B1617/84 and B1618/84 are not output.
A
DTC B1602/83, B1603/83, B1612/83, and B1613/83 are output
B
B1607/84, B1608/84, B1617/ 84 and B1618/84 are output
C
- HINT:
- DTCs other than DTC B1602/83, B1603, B1612/83, B1613/83, B1607/84, B1608/84, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | ||
| ||
| 7. CHECK ENGINE ROOM MAIN WIRE (OPEN) |
![]() ![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Disconnect the service wire from connector E.
Disconnect the engine room main wire connector from the instrument panel wire.
Using a service wire, connect AE9-2 (+SR) and AE9-1 (-SR) of connector D.
- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
A45-2 (+SR) - A45-1 (-SR)
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 8. CHECK ENGINE ROOM MAIN WIRE (SHORT) |
![]() ![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
AE9-1 (+SR) - AE9-2 (-SR)
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 9. CHECK ENGINE ROOM MAIN WIRE (TO B+) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the engine room main wire connector from the instrument panel wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
AE9-1 (+SR) - Body ground
Below 1 V
AE9-2 (-SR) - Body ground
Below 1 V
|
|
||||
| OK | ||
| ||
| 10. CHECK ENGINE ROOM MAIN WIRE (TO GROUND) |
![]() ![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
AE9-1 (+SR) - Body ground
1 MΩ or higher
AE9-2 (-SR) - Body ground
1 MΩ or higher
|
|
||||
| OK | ||
| ||





