B1607/84 Lost Communication with Front Satellite Sensor Bus LH
Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006
Also covers:
- B1608/84 Front Satellite Sensor Bus LH Initialization Incomplete
- B1617/84 Lost Communication with Front Airbag Sensor LH
- B1618/84 Front Airbag Sensor LH Initialization Incomplete
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
DESCRIPTION
The front airbag sensor LH consists of the diagnostic circuit and the frontal deceleration sensor.If the center airbag sensor receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1607/84, B1608/84, B1612/84 or B1613/84 is recorded when a malfunction is detected in the front airbag sensor LH circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1607/84 B1608/84 B1618/84 B1618/84 |
When one of following conditions is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor LH.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 2. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN) |
![]() ![]() |
Disconnect the connectors from the center airbag sensor and the front airbag sensor LH.
Using a service wire, connect A22-2 (+SL) and A22-1 (-SL) of connector E.
- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E49-30 (+SL) - E49-28 (-SL)
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT) |
![]() ![]() |
Disconnect the service wire from connector E.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E49-30 (+SL) - E49-28 (-SL)
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO B+) |
![]() ![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
E49-30 (+SL) - Body ground
Below 1 V
E49-28 (-SL) - Body ground
Below 1 V
|
|
||||
| OK | |
| 5. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO GROUND) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E49-30 (+SL) - Body ground
1 MΩ or higher
E49-28 (-SL) - Body ground
1 MΩ or higher
|
|
||||
| OK | |
| 6. CHECK FRONT AIRBAG SENSOR LH |
![]() ![]() |
Connect the connectors to the center airbag sensor.
Interchange the front airbag sensor RH and LH, and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
Result Result
Proceed to
DTC B1602/83, B1603/83, B1612/83, B1613/83, B1607/84, B1608/84, B1617/84 and B1618/84 are not output.
A
DTC B1607/84, B1608/84, B1617/84 and B1618/84 are output
B
DTC B1602/83, B1603/83, B1612/83 and B1613/83 are output
C
- HINT:
- DTCs other than DTC B1602/83, B1603/83, B1612/83, B1613/83, B1607/84, B1608/84, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | ||
| ||
| 7. CHECK ENGINE ROOM MAIN WIRE (OPEN) |
![]() ![]() |
Disconnect the service wire from connector E.
Disconnect the engine room main wire connector from the instrument panel wire.
Using a service wire, connect AE5-1 (+SL) and AE5-2 (-SL) of connector D.
- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector when connecting.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
A22-2 (+SL) - A22-1 (-SL)
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 8. CHECK ENGINE ROOM MAIN WIRE (SHORT) |
![]() ![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
AE5-1 (+SL) - AE5-2 (-SL)
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 9. CHECK ENGINE ROOM MAIN WIRE (TO B+) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the engine room main wire connector from the instrument panel wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
AE5-1 (+SL) - Body ground
Below 1 V
AE5-2 (-SL) - Body ground
Below 1 V
|
|
||||
| OK | ||
| ||
| 10. CHECK ENGINE ROOM MAIN WIRE (TO GROUND) |
![]() ![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
AE5-1 (+SL) - Body ground
1 MΩ or higher
AE5-2 (-SL) - Body ground
1 MΩ or higher
|
|
||||
| OK | ||
| ||





