2005-2008 RAV4 · Service Manual RESTRAINTS

B1607/84 Lost Communication with Front Satellite Sensor Bus LH

Diagnostic trouble codes · Vehicles built from Jan 2007

Also covers:

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

The front airbag sensor LH consists of the diagnostic circuit and the frontal deceleration sensor.
If the center airbag sensor receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1607/84, B1608/84, B1612/84 or B1613/84 is recorded when a malfunction is detected in the front airbag sensor LH circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1607/84
B1608/84
B1618/84
B1618/84
When one of following conditions is met:
  1. Center airbag sensor detects line short signal, open signal, short to ground signal or short to B+ signal in the front airbag sensor LH circuit for 2 seconds.
  2. Front airbag sensor LH malfunction
  3. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor LH
  4. Center airbag sensor

WIRING DIAGRAM

C123527E05

INSPECTION PROCEDURE


1. CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTOR
OK


2. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)
H100831E08
  1. Disconnect the connectors from the center airbag sensor and the front airbag sensor LH.

  1. Using a service wire, connect A22-2 (+SL) and A22-1 (-SL) of connector E.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E49-30 (+SL) - E49-28 (-SL)
    Below 1 Ω



NG
Go to step 7
OK


3. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)
H100832E09
  1. Disconnect the service wire from connector E.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E49-30 (+SL) - E49-28 (-SL)
    1 MΩ or higher



NG
Go to step 8
OK


4. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO B+)
H100832E09
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E49-30 (+SL) - Body ground
    Below 1 V
    E49-28 (-SL) - Body ground
    Below 1 V



NG
Go to step 9
OK


5. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO GROUND)
H100832E09
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E49-30 (+SL) - Body ground
    1 MΩ or higher
    E49-28 (-SL) - Body ground
    1 MΩ or higher



NG
Go to step 10
OK


6. CHECK FRONT AIRBAG SENSOR LH
C128728E02
  1. Connect the connectors to the center airbag sensor.

  1. Interchange the front airbag sensor RH and LH, and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1602/83, B1603/83, B1612/83, B1613/83, B1607/84, B1608/84, B1617/84 and B1618/84 are not output.
    A
    DTC B1607/84, B1608/84, B1617/84 and B1618/84 are output
    B
    DTC B1602/83, B1603/83, B1612/83 and B1613/83 are output
    C

    HINT:
    DTCs other than DTC B1602/83, B1603/83, B1612/83, B1613/83, B1607/84, B1608/84, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY

C
REPLACE FRONT AIRBAG SENSOR LH
A

USE SIMULATION METHOD TO CHECK

7. CHECK ENGINE ROOM MAIN WIRE (OPEN)
C123537E03
  1. Disconnect the service wire from connector E.

  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Using a service wire, connect AE5-1 (+SL) and AE5-2 (-SL) of connector D.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection
Specified Condition
A22-2 (+SL) - A22-1 (-SL)
Below 1 Ω



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

8. CHECK ENGINE ROOM MAIN WIRE (SHORT)
C128729E03
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    AE5-1 (+SL) - AE5-2 (-SL)
    1 MΩ or higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

9. CHECK ENGINE ROOM MAIN WIRE (TO B+)
C128729E03
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    AE5-1 (+SL) - Body ground
    Below 1 V
    AE5-2 (-SL) - Body ground
    Below 1 V



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

10. CHECK ENGINE ROOM MAIN WIRE (TO GROUND)
C128729E03
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    AE5-1 (+SL) - Body ground
    1 MΩ or higher
    AE5-2 (-SL) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE


← B1607/84 Lost Communication with Front Satellite Sensor Bus LH (+ B1608/84, B1617/84, B1618/84) (Nov 2005 – Dec 2006)B1610/13 Front Airbag Sensor RH Circuit Malfunction (Nov 2005 – Dec 2006) →