2005-2008 RAV4 · Service Manual BRAKE

C0273/13 Open in ABS Motor Relay Circuit

Diagnostic trouble codes · Vehicles built from Aug 2007

Also covers:

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

The ABS motor relay supplies the power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay ON and operates the ABS pump motor.
DTC No.
DTC Detection Condition
Trouble Area
C0273/13
When either condition below is met:
  1. All of following conditions continue for 0.2 seconds or more.
    1. IG1 terminal voltage between 9.5 V and 18.5 V.
    2. During initial check or ABS operation.
    3. Relay contact open when relay on.
  2. Both of following conditions continue for 0.12 seconds or more.
    1. IG1 terminal voltage is 9.5 V or less.
    2. Relay contact remains open when relay on.
  1. ABS1 H-fuse
  2. Wire harness (+BM circuit)
  3. Brake actuator
C0274/14
When motor relay off, motor relay remains closed for 4 seconds or more.
  1. ABS1 H-fuse
  2. Wire harness (+BM circuit)
  3. Brake actuator

HINT:
C0273/13 and C0274/14: The skid control ECU begins to detect these DTCs when the vehicle speed exceeds 6 km/h (4 mph).


WIRING DIAGRAM

Refer to DTC C0226/21, C0236/22, C0246/23, C0256/24 (Click here).

INSPECTION PROCEDURE


1. INSPECT FUSE (ABS1)
  1. Remove the ABS1 H-fuse from the engine room No. 1 relay block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2. CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)

  1. C117862E06
    Disconnect the A27 ECU connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A27-23 (+BM) - Body ground
    10 to 14 V

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A27-2 (GND1) - Body ground
    Below 1 Ω
    A27-24 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MOTOR RELAY)
  1. Select the Active Test, generate a control command, and then check that the motor relay operates.

    Skid control ECU 
    Item (Display)
    Vehicle Condition / Test Details
    Diagnostic Note
    Motor Relay
    Turns ABS motor relay ON / OFF
    Operating sound of motor can be heard

    OK:
    Operation sound of the ABS motor is heard.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at 6 km/h (4 mph) or more to activate the initial check.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY


← C0273/13 Open in ABS Motor Relay Circuit (+ C0274/14) (Jan 2007 – Jul 2007)C0278/11 Open in ABS Solenoid Relay Circuit (+ C0279/12) (Nov 2005 – Dec 2006) →