2005-2008 RAV4 · Service Manual BRAKE

C0278/11 Open in ABS Solenoid Relay Circuit

Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007

Also covers:

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008

DESCRIPTION

The solenoid relay supplies power to the ABS solenoid and TRC solenoid.
After the ignition switch is turned on, the vehicle speed has reached 6 km/h (4 mph) and the solenoid is determined to be normal by the initial check self-diagnosis, the relay switches on. If any open or short circuits are detected, the relay switches off.
These DTCs may be set if the voltage supply to the solenoid relay (+BS) falls below the DTC detection threshold due to the battery or alternator outputs being insufficient.
DTC No.
DTC Detection Condition
Trouble Area
C0278/11
When either condition below is met:
  1. Both of following conditions continue for 0.2 seconds or more.
    1. IG1 terminal voltage between 9.5 V and 18.5 V.
    2. Solenoid relay contact open when relay on.
  2. Both of following conditions continue for 0.2 seconds or more.
    1. IG1 terminal voltage becomes lower than 9.5 V when relay turned on.
    2. Relay contact remains open.
  1. ABS2 H-fuse
  2. Wire harness (+BS circuit)
  3. ABS and TRACTION actuator
C0279/12
Immediately after ignition switch turned on, solenoid relay contact closed for 0.2 seconds or more when relay off.
  1. ABS2 H-fuse
  2. Wire harness (+BS circuit)
  3. ABS and TRACTION actuator

HINT:
DTCs C0278/11 and C0279/12: The skid control ECU begins to detect these DTCs when the vehicle speed exceeds 6 km/h (4 mph).


WIRING DIAGRAM

Refer to DTC C0273/13, C0274/14, C1361/91 (Click here).

INSPECTION PROCEDURE


1. INSPECT FUSE
  1. Remove the ABS2 H-fuse from the engine room No. 1 relay block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2. CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)

  1. C121700E31
    Disconnect the A26 ECU connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A26-31 (+BS) - Body ground
    10 to 14 V

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A26-32 (GND1) - Body ground
    Below 1 Ω
    A26-1 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at 6 km/h (4 mph) or more to activate the initial check.

  1. Check if the same DTCs is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY


← C0278/11 Open in ABS Solenoid Relay Circuit (+ C0279/12) (Nov 2005 – Dec 2006)C0278/11 Open in ABS Solenoid Relay Circuit (+ C0279/12) (Aug 2007 – Jul 2008) →