2005-2008 RAV4 · Service Manual BRAKE

C0273/13 Open in ABS Motor Relay Circuit

Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007

Also covers:

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008

DESCRIPTION

If a DTC related to the motor line is stored, the VSC FAIL (fail-safe) relay cuts off the power supply to the VSC MTR relay and performs the fail-safe operation.
While the ABS, TRC, VSC, or BA is operating, the skid control ECU turns the VSC FAIL relay on and activates the pump motor in the ABS and TRACTION actuator.
These DTCs may be stored if the motor relay (+BM) voltage becomes lower than the DTC detecting condition due to insufficient output from the battery or alternator.
DTC No.
DTC Detection Condition
Trouble Area
C0273/13
When either condition below is met:
  1. All of following conditions continue for 0.12 seconds or more.
    1. IG1 terminal voltage between 9.5 V and 18.5 V.
    2. During initial check or ABS/TRC/VSC/BA.
    3. Relay contact open when relay on.
  2. Both of following conditions continue for 0.12 seconds or more.
    1. IG1 terminal voltage 9.5 V or less.
    2. Relay contact remains open when relay on.
  1. ABS1 H-fuse
  2. VSC MTR relay
  3. VSC MTR relay circuit
  4. VSC FAIL relay
  5. VSC FAIL relay circuit
  6. ABS and TRACTION actuator
C0274/14
Despite motor relay (VSC MTR relay) off, motor relay remains closed for 4 seconds or more.
  1. ABS1 H-fuse
  2. VSC MTR relay
  3. VSC MTR relay circuit
  4. VSC FAIL relay
  5. VSC FAIL relay circuit
  6. ABS and TRACTION actuator
C1361/91
Immediately after ignition switch on (IG), motor fail-safe relay (VSC FAIL relay) contact closed for 4 seconds when motor fail-safe relay (VSC FAIL relay) off.
  1. ABS1 H-fuse
  2. VSC MTR relay
  3. VSC MTR relay circuit
  4. VSC FAIL relay
  5. VSC FAIL relay circuit
  6. ABS and TRACTION actuator

HINT:
DTCs C0273/13, C0274/14 and C1361/91: The skid control ECU begins to detect these DTCs when the vehicle speed exceeds 6 km/h (4 mph).


WIRING DIAGRAM

C126307E01

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MOTOR RELAY)
  1. Select the Active Test, generate a control command, and then check that the ABS motor relay operates.

    Skid control ECU 
    Item (Display)
    Test Details
    Diagnostic Note
    Motor Relay
    Turns ABS motor relay ON / OFF
    Operating sound of motor can be heard

    OK:
    The operation sound of the ABS motor can be heard.



OK
Go to step 8
NG


2. INSPECT FUSE (ABS1)
  1. Remove the ABS1 H-fuse from the engine room No. 1 relay block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


3. INSPECT VSC MOTOR RELAY (Marking: VSC MTR)

  1. A092673E05
    Remove the VSC motor relay from the engine room No. 1 relay block.

  1. Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)



NG
REPLACE VSC MOTOR RELAY
OK


4. INSPECT FAIL-SAFE RELAY (Marking: VSC FAIL)

  1. B060778E62
    Remove the faile-safe relay from the engine room No. 1 relay block.

  1. Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)



NG
REPLACE FAIL-SAFE RELAY
OK


5. CHECK WIRE HARNESS (FAIL-SAFE RELAY - BATTERY)

  1. C126326E01
    Remove the fail-safe relay from the engine room No. 1 relay block.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    VSC FAIL relay terminal 5 - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6. CHECK ENGINE ROOM NO. 1 RELAY BLOCK (FAIL-SAFE RELAY - VSC MOTOR RELAY)

  1. C126304E01
    Remove the fail-safe and VSC motor relays from the engine room No. 1 relay block.

  1. Measure the resistance of the relay terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    VSC FAIL relay terminal 3 - VSC MTR relay terminal 5
    Below 1 Ω
    VSC FAIL relay terminal 3 - Body ground
    10 kΩ or higher



NG
REPLACE ENGINE ROOM NO. 1 RELAY BLOCK
OK


7. CHECK WIRE HARNESS (ENGINE ROOM NO. 1 RELAY BLOCK - SKID CONTROL ECU)

  1. C126327E03
    Disconnect the A26 ECU connector.

  1. Remove the fail-safe and VSC motor relays from the engine room No. 1 relay block.

  1. Measure the resistance of the wire harness connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A26-2 (BM) - VSC MTR relay terminal 3
    Below 1 Ω
    A26-14 (MRF) - VSC FAIL relay terminal 2
    Below 1 Ω
    A26-15 (MR) - VSC MTR relay terminal 2
    Below 1 Ω
    A26-45 (R+) - VSC FAIL relay terminal 1
    Below 1 Ω
    A26-2 (BM) - Body ground
    10 kΩ or higher
    A26-14 (MRF) - Body ground
    10 kΩ or higher
    A26-15 (MR) - Body ground
    10 kΩ or higher
    A26-45 (R+) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at 6 km/h (4 mph) or more to activate the initial check.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY


← C0273/13 Open in ABS Motor Relay Circuit (+ C0274/14, C1361/91) (Nov 2005 – Dec 2006)C0273/13 Open in ABS Motor Relay Circuit (+ C0274/14, C1361/91) (Aug 2007 – Jul 2008) →