C0273/13 Open in ABS Motor Relay Circuit
Diagnostic trouble codes · Vehicles built Aug 2007 – Jul 2008
Also covers:
- C0274/14 Short to B+ in ABS Motor Relay Circuit
- C1361/91 Short Circuit in ABS Motor Fail Safe Relay Circuit
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008
DESCRIPTION
If a DTC related to the motor line is stored, the VSC FAIL (fail-safe) relay cuts off the power supply to the VSC MTR relay and performs the fail-safe operation.While the ABS, TRC, VSC, or BA is operating, the skid control ECU turns the VSC FAIL relay on and activates the pump motor in the ABS and TRACTION actuator.
These DTCs may be stored if the motor relay (+BM) voltage becomes lower than the DTC detecting condition due to insufficient output from the battery or alternator.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| C0273/13 |
When either condition below is met:
|
|
| C0274/14 |
Despite motor relay (VSC MTR relay) off, motor relay remains closed for 4 seconds or more. |
|
| C1361/91 |
Immediately after ignition switch on (IG), motor fail-safe relay (VSC FAIL relay) contact closed for 4 seconds when motor fail-safe relay (VSC FAIL relay) off. |
|
- HINT:
- DTCs C0273/13, C0274/14 and C1361/91: The skid control ECU begins to detect these DTCs when the vehicle speed exceeds 6 km/h (4 mph).
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MOTOR RELAY) |
Select the Active Test, generate a control command, and then check that the ABS motor relay operates.
Skid control ECU Item (Display)
Test Details
Diagnostic Note
Motor Relay
Turns ABS motor relay ON / OFF
Operating sound of motor can be heard
- OK:
- The operation sound of the ABS motor can be heard.
|
|
||||
| NG | |
| 2. INSPECT FUSE (ABS1) |
Remove the ABS1 H-fuse from the engine room No. 1 relay block.
Measure the resistance of the fuse.
- Standard resistance:
- Below 1 Ω
|
|
||||
| OK | |
| 3. INSPECT VSC MOTOR RELAY (Marking: VSC MTR) |
Remove the VSC motor relay from the engine room No. 1 relay block.

Measure the resistance of the relay.
- Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)
|
|
||||
| OK | |
| 4. INSPECT FAIL-SAFE RELAY (Marking: VSC FAIL) |
Remove the faile-safe relay from the engine room No. 1 relay block.

Measure the resistance of the relay.
- Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)
|
|
||||
| OK | |
| 5. CHECK WIRE HARNESS (FAIL-SAFE RELAY - BATTERY) |
Remove the fail-safe relay from the engine room No. 1 relay block.

Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
VSC FAIL relay terminal 5 - Body ground
10 to 14 V
|
|
||||
| OK | |
| 6. CHECK ENGINE ROOM NO. 1 RELAY BLOCK (FAIL-SAFE RELAY - VSC MOTOR RELAY) |
Remove the fail-safe and VSC motor relays from the engine room No. 1 relay block.

Measure the resistance of the relay terminals.
- Standard resistance:
Tester Connection
Specified Condition
VSC FAIL relay terminal 3 - VSC MTR relay terminal 5
Below 1 Ω
VSC FAIL relay terminal 3 - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 7. CHECK WIRE HARNESS (ENGINE ROOM NO. 1 RELAY BLOCK - SKID CONTROL ECU) |
Disconnect the A26 ECU connector.

Remove the fail-safe and VSC motor relays from the engine room No. 1 relay block.
Measure the resistance of the wire harness connectors.
- Standard resistance:
Tester Connection
Specified Condition
A26-2 (BM) - VSC MTR relay terminal 3
Below 1 Ω
A26-14 (MRF) - VSC FAIL relay terminal 2
Below 1 Ω
A26-15 (MR) - VSC MTR relay terminal 2
Below 1 Ω
A26-45 (R+) - VSC FAIL relay terminal 1
Below 1 Ω
A26-2 (BM) - Body ground
10 kΩ or higher
A26-14 (MRF) - Body ground
10 kΩ or higher
A26-15 (MR) - Body ground
10 kΩ or higher
A26-45 (R+) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 8. RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at 6 km/h (4 mph) or more to activate the initial check.
Check if the same DTC(s) is output (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | ||
| ||
