2005-2008 RAV4 · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2007


1. REMOVE ENGINE WITH TRANSAXLE
  1. Remove the engine with transaxle (Click here)


2. REMOVE FRONT CROSS MEMBER SUB-ASSEMBLY

  1. A139135
    Remove the bolt, nut and crossmember.


3. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

  1. A171020
    Remove the bolt and suspension crossmember.


4. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine.


5. REMOVE STARTER ASSEMBLY

  1. A126954
    Disconnect the starter connector.

  1. Open the terminal cap, remove the nut and disconnect the starter wire.

  1. A126955
    Remove the 2 bolts and starter.


6. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

  1. D030471E01
    Remove the 2 bolts and flywheel housing under cover.

  1. D030472E01
    Turn the crankshaft to gain access and remove the 6 bolts while holding the crankshaft pulley bolt with a wrench.

  1. C136364
    Remove the 3 lower side mounting bolts.

  1. C134974
    Remove the 7 upper side mounting bolts.

  1. Separate and remove the automatic transaxle.


7. REMOVE TRANSFER ASSEMBLY

C126622
  1. Remove the 6 nuts, 2 bolts and transfer from the transaxle.


8. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

  1. A129631E01
    Using SST, hold the crankshaft.
    SST
    09213-70011   (09213-70020)
    09330-00021  

  1. A076327E03
    Remove the 8 bolts, front spacer, drive plate and rear spacer.

    NOTICE:
    Do not reuse the bolts.


9. INSTALL ENGINE TO ENGINE STAND
  1. Install the engine to an engine stand. Remove the sling device and chain block from the engine.


10. REMOVE INTAKE AIR SURGE TANK ASSEMBLY

  1. A129464
    Disconnect the 2 water by-pass hoses from the throttle body.

  1. Disconnect the vapor feed hose.

  1. Disconnect the throttle body connector and clamp.

  1. A129467
    Disconnect the connector.

  1. Disconnect the No. 1 ventilation hose and vacuum hose.

  1. Remove the 2 bolts and throttle body bracket.

  1. Remove the 2 bolts and No. 1 surge tank stay.

  1. A139209
    Using a 5 mm socket hexagon wrench, remove the 4 bolts.

  1. Remove the 2 nuts and surge tank.

  1. Remove the gasket from the surge tank.


11. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 6 bolts and 6 coils from the cylinder head.


12. REMOVE NO. 2 ENGINE MOUNTING STAY RH
  1. Remove the bolt and mounting stay.


13. REMOVE INTAKE MANIFOLD

  1. A076533E01
    Remove the 6 bolts, 4 nuts, intake manifold and 2 gaskets.


14. REMOVE MANIFOLD STAY

  1. A171613
    Remove the 2 bolts, nut and manifold stay.


15. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
  1. Disconnect the air fuel ratio sensor connector clamp.

  1. A133291
    Uniformly loosen and remove the 6 nuts.

  1. Remove the manifold and gasket.


16. REMOVE V-RIBBED BELT

  1. A137895
    Rotate the tensioner pulley counterclockwise to loosen the belt tension. Then remove the V-ribbed belt.

  1. A095070E01
    While turning the belt tensioner counterclockwise, align its holes, and then insert a 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner in place.


17. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A118311
    Remove the bolt, plate and idler pulley.


18. REMOVE COOLER COMPRESSOR ASSEMBLY

  1. H102369
    Disconnect the connector.

  1. Remove the 4 bolts and cooler compressor.


19. REMOVE GENERATOR ASSEMBLY

  1. A132430
    Disconnect the 2 wire harness clamps.

  1. A132431
    Remove the terminal cap.

  1. Remove the nut and disconnect the generator wire from terminal B.

  1. Disconnect the generator connector from the generator.

  1. A132432E01
    Remove the bolt from the cylinder block.

  1. A132433
    Remove the 2 bolts and generator.


20. REMOVE OIL DIPSTICK GUIDE
  1. Remove the dipstick.

  1. A129638E01
    Remove the 2 bolts, and the No. 1 and No. 2 guides.

  1. Remove the O-rings from the guide.


21. REMOVE NO. 2 MANIFOLD STAY

  1. A139521
    Remove the bolt, nut and manifold stay.


22. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
  1. Remove the 3 bolts and insulator.


23. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

  1. A139492
    Uniformly loosen and remove the 6 nuts.

  1. Remove the manifold and gasket.


24. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A129644
    Remove the 5 bolts and V-ribbed belt tensioner assembly.


25. REMOVE NO. 2 TIMING GEAR COVER
  1. Remove the 2 bolts and gear cover.


26. REMOVE WATER PUMP PULLEY

  1. A132444E01
    Using SST, hold the water pump pulley.
    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 4 bolts and water pump pulley.


27. REMOVE RADIO SETTING CONDENSER

  1. A132991
    Remove the 2 bolts and 2 radio setting condensers.


28. REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY

  1. A132992
    Remove the bolt and No. 1 vacuum switching valve.


29. REMOVE CRANKSHAFT PULLEY

  1. A132066E01
    Using SST, loosen the crankshaft pulley set bolt.
    SST
    09213-70011   (09213-70020)
    09330-00021  

  1. A132067E01
    Using the pulley set bolt and SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)


30. REMOVE WATER INLET HOUSING

  1. A132442E01
    Disconnect the water hose.

  1. Remove the 2 bolts, nut and water inlet housing.

  1. A132443
    Remove the water inlet housing No. 1 gasket and water outlet pipe O-ring.


31. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A132107
    Remove the 16 bolts and 2 nuts.

  1. A132161
    Insert the blade of an oil pan seal cutter between the oil pans, cut through the applied sealer and remove the oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.


32. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A132108
    Remove the bolt, 2 nuts, oil strainer and gasket.


33. REMOVE OIL PAN SUB-ASSEMBLY

  1. A132109
    Remove the 16 bolts and 2 nuts.

    HINT:
    Be sure to clean the bolts and stud bolts and check the threads for cracks or other damage.

  1. A132110
    Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.

  1. A132111
    Remove the 2 O-rings from the oil pump.


34. REMOVE NO. 1 OIL PIPE

  1. A135726E01
    Remove the 2 oil pipe unions, gaskets and oil pipe.

  1. Remove the oil control valve filter LH and gaskets.


35. REMOVE OIL PIPE

  1. A134878E01
    Remove the bolt.

  1. Remove the 2 oil pipe unions and oil pipe.

  1. Remove the oil control valve filter RH and gaskets.


36. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)

  1. A132119
    Remove the 12 bolts, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same locations they were removed from.


37. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)

  1. A132120
    Remove the 12 bolts, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same locations they were removed from.


38. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A132150
    Remove the 23 bolts and 2 nuts as shown in the illustration.

  1. A132099
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Do not damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.

  1. A132100
    Remove the gasket.


39. REMOVE TIMING CHAIN COVER OIL SEAL

  1. A128007E03
    Using a screwdriver, pry out the oil seal.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.

  1. A132052E01
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.
    SST
    09316-60011   (09316-00011)

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the oil seal at an angle.
    3. Make sure that the oil seal edge does not stick out of the timing chain case.

  1. Apply MP grease to the lip of the oil seal.


40. SET NO. 1 CYLINDER TO TDC / COMPRESSION
  1. Temporarily tighten the pulley set bolt.

  1. A132112E01
    Set the timing mark on the crank angle sensor plate to the RH block bore center line (TDC / compression).

  1. A132113E01
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) and align the timing marks as in the previous step.


41. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A131978E01
    Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.

  1. Remove the 2 bolts and chain tensioner.


42. REMOVE CHAIN TENSIONER SLIPPER

43. REMOVE NO. 1 CHAIN SUB-ASSEMBLY

  1. A132114E01
    Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing gear.

  1. Remove the chain from the crankshaft timing gear and place it on the crankshaft.

  1. A132098E01
    Turn the camshaft timing gear on the RH bank clockwise (approximately 60°) and set it as shown in the illustration. Be sure to loosen the chain between the center banks.

  1. Remove the chain.


44. REMOVE IDLE SPROCKET ASSEMBLY

  1. A129695
    Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket and No. 1 idle gear shaft.


45. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

  1. A132072E01
    While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix it in place.

  1. A132073E01
    Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts and 2 camshaft timing gears.

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing gear.

  1. Remove the No. 2 chain.


46. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A132046
    Remove the bolt and chain tensioner.


47. REMOVE CAMSHAFT BEARING CAP (for Bank 1)

  1. A132121
    Remove the 3 gaskets.

  1. A132139E01
    Make sure that the knock pin of the camshaft is positioned as shown in the illustration.

  1. A132122E01
    Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.

  1. A132123E01
    Uniformly loosen and remove the 12 bearing cap bolts in several steps and in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 bearing caps.


48. REMOVE NO. 1 CAMSHAFT
  1. Remove the No. 1 camshaft.


49. REMOVE NO. 2 CAMSHAFT
  1. Remove the No. 2 camshaft.


50. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY (for Bank 1)

  1. A132124
    Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.

    HINT:
    Tape the screwdriver tip before use.

← COMPONENTS (from Aug 2007)INSTALLATION (from Aug 2007) →