Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for RHD)

STEERING COLUMN ASSEMBLY (for RHD) > INSTALLATION

for Preparation Click here



1. INSTALL STEERING COLUMN ASSEMBLY


C127472
  1. Install the steering column onto the instrument panel reinforcement with the 3 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect all the connectors and clamp the wire harnesses onto the steering column bracket.



2. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY
  1. Install the brake pedal support (Click here).



3. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY NO.2


C128805E02
  1. Align the matchmarks on the steering intermediate shaft and steering sliding yoke and temporarily install them with bolt B.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Align the matchmarks on the steering sliding yoke and steering gear assembly and install them with bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



4. INSTALL AIR DUCT


C127470E02


5. INSTALL COLUMN HOLE COVER SILENCER SHEET


C127468
  1. Install the column hole cover plate with the 2 clips.

  1. Install the floor carpet.



6. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Knee Airbag)


B127987
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Install the driver side knee airbag with the 4 bolts.

    Torque:
    10 N*m{ 101 kgf*cm , 7 ft.*lbf }



7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)


B132919
  1. Attach the 8 claws to install the lower instrument panel finish panel.

  1. Install the 2 screws.



8. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Driver Side Knee Airbag)


    B129996
  1. Attach 3 claws to install the instrument panel under cover.

  1. Install the 2 screws.



9. CONNECT POWER STEERING ECU


C128907E03
  1. Connect the 2 steering column connectors to the power steering ECU.

  1. Install the power steering motor harness and torque sensor wire harness clamps onto the side of the power steering ECU.

  1. Tilt the steering column up and down to make sure that the power steering motor wire harness and torque sensor wire harness do not interfere with any components.



10. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Install the instrument panel .



11. INSTALL COMBINATION SWITCH ASSEMBLY


C127467
  1. Install the turn signal switch onto the steering column with the clamp.



12. INSTALL SPIRAL CABLE SUB-ASSEMBLY
  1. Install the spiral cable onto the turn signal switch.



    C127466E01
  1. Connect all the connectors to the turn signal switch with spiral cable.



13. INSTALL STEERING COLUMN COVER


    C127465
  1. Attach the claw to install the steering column cover upper.



    C127464
  1. Attach the 4 claws to install the steering column cover lower.



14. INSTALL STEERING WHEEL ASSEMBLY


    C132125E02
  1. Align the matchmarks and install the steering wheel onto the steering column.

  1. Install the nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect all the connectors to the spiral cable.



15. INSTALL STEERING PAD (for Torx Type)


B127893E01
  1. Support the steering pad with one hand as shown in the illustration.

  1. Connect the 2 airbag connectors.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Connect the horn connector.

  1. Install the steering pad after confirming that the circumference grooves of the screws are caught on the screw case.



    B130245E02
  1. Using a T30 "torx" driver, install the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



16. INSTALL STEERING PAD (for Pin Type)


B220979
  1. Support the steering pad with one hand as shown in the illustration.

  1. Connect the 2 airbag connectors.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Connect the horn connector.

  1. Install the steering pad after confirming that the circumference grooves of the screws are caught on the screw case.

  1. Attach the 2 spring to steering pad.



17. POSITION FRONT WHEELS FACING STRAIGHT AHEAD


18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


19. INSPECT SRS WARNING LIGHT
  1. Inspect SRS warning light (Click here).