Home › BRAKE › BRAKE › BRAKE PEDAL

BRAKE PEDAL > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY


    C126454
  1. Install the support with the 4 nuts.

    Torque:
    12.7 N*m{ 130 kgf*cm , 9 ft.*lbf }



    C129086E01
  1. Install the bolt to the support.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }



2. INSTALL PUSH ROD PIN



C130666E11



C130668E05

  1. Apply lithium soap base glycol grease to the push rod pin.

  1. Install the push rod pin to the push rod clevis.

    NOTICE:
    The push rod pin must be installed as shown in the illustration.

  1. Install the clip to the push rod pin.

    NOTICE:
    The clip must be installed as shown in the illustration.



3. INSTALL STOP LIGHT SWITCH ASSEMBLY


    C111301E03
  1. Insert the switch into the adjuster until the switch body touches the pedal.

    NOTICE:
    Do not depress the pedal.



    C111302E02
  1. Turn the switch a quarter turn clockwise.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

    NOTICE:
    Do not depress the pedal.

  1. Check the switch clearance.

    Standard stop light switch clearance:
    0.5 to 2.6 mm (0.020 to 0.102 in.)



4. CONNECT CONNECTORS
  1. w/ VSC:
    Connect the brake pedal load sensing switch connector.

  1. Connect the stop light switch connector.



5. CHECK AND ADJUST BRAKE PEDAL HEIGHT


    C200684E02
    C200685E01
  1. Check the pedal height.

    Standard pedal height from dash panel:
    Item
    Specified Condition
    for LHD
    184.2 to 194.2 mm (7.252 to 7.646 in.)
    for RHD
    168.6 to 178.6 mm (6.638 to 7.031 in.)



  1. Adjust the pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Remove the switch.

    3. Loosen the push rod clevis lock nut.

    4. Adjust the pedal height by turning the push rod.

    5. Tighten the lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }



    6. C111301E03
    7. Insert the switch into the adjuster until the switch body touches the pedal.

      NOTICE:
      Do not depress the pedal.



    8. C111302E02
    9. Turn the switch a quarter turn clockwise.

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

      NOTICE:
      Do not depress the pedal.

    10. Connect the connector to the switch.

    11. Check the switch clearance.

      Standard stop light switch clearance:
      0.5 to 2.6 mm (0.020 to 0.102 in.)



6. CHECK BRAKE PEDAL FREE PLAY


C111306E01
  1. Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.

  1. Depress the pedal until resistance is felt.

  1. Check the pedal free play by measuring the distance between the position in the previous step and the pedal released position.

    Standard pedal free play:
    1.0 to 6.0 mm (0.039 to 0.236 in.)

    If the free play is not as specified, check the switch clearance in the next step.
    If the free play is as specified, proceed to the "CHECK BRAKE PEDAL RESERVE DISTANCE" procedure.

  1. Check the switch clearance.

    Standard stop light switch clearance:
    0.5 to 2.6 mm (0.020 to 0.102 in.)

    If the clearance is not as specified, reinstall the switch and recheck the pedal's free play.
    If the clearance is as specified, troubleshoot the brake system and proceed to the "CHECK BRAKE PEDAL RESERVE DISTANCE" procedure.



7. CHECK BRAKE PEDAL RESERVE DISTANCE
  1. Release the parking brake lever. Start the engine.

  1. Depress the pedal and check the pedal reserve distance.

    1. Depress the pedal with a force of 490 N (50 kgf, 110 lbf).

    2. Measure the distance between the pedal and dash panel.

      Standard pedal reserve distance:
      Item
      Specified Condition
      for 2AD-FTV
      for LHD without VSC
      More than 75 mm (2.95 in.)
      for LHD with VSC
      More than 110 mm (4.33 in.)
      for RHD without VSC
      More than 70 mm (2.75 in.)
      for RHD with VSC
      More than 100 mm (3.93 in.)
      for 2AD-FHV
      for LHD without VSC
      More than 75 mm (2.95 in.)
      for LHD with VSC
      More than 110 mm (4.33 in.)
      for RHD without VSC
      More than 70 mm (2.75 in.)
      for RHD with VSC
      More than 100 mm (3.93 in.)

      If the distance is not as specified, troubleshoot the brake system.



8. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. Install the instrument panel (Click here).



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL