Home › TRANSMISSION ยท U660F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / (desired system) / Data List.

  7. According to the display on the tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Actual vehicle speed
    -
    Engine Speed
    Engine speed/
    Min.: 0 rpm
    Max.: 16383.75 rpm
    Engine idling: 720 to 820 rpm
    -
    Calculate Load
    Calculated load by ECM/
    Min.: 0%
    Max.: 100%
    1. Engine idling: 7 to 26%
    2. Running without load (2500 rpm): 10 to 20%
    -
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C (-40°F)
    Max.: 140°C (284°F)
    After warming up engine: 60 to 90°C (140 to 194°F)
    1. If the value is -40°C (-40°F), the sensor circuit is open.
    2. If the value is 140°C (284°F), the sensor circuit is shorted.
    Engine Run Time
    Engine run time/
    Min.: 0 seconds,
    Max.: 65535 seconds
    Time after engine start
    -
    Battery Voltage
    Battery voltage/
    Min.: 0 V
    Max.: 65.535 V
    Engine idling: 11 to 14 V
    -
    Starter Signal
    Starter signal/
    ON or OFF
    1. Engine cranking: ON
    2. Engine not cranking: OFF
    -
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in P or N
    2. OFF: Shift lever not in P or N
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Stop Light Switch
    Stop light switch status/
    ON or OFF
    1. ON: Brake pedal depressed
    2. OFF: Brake pedal released
    -
    MIL ON Run Distance
    MIL on run distance/
    Min.: 0 km (0 mile),
    Max.: 65535 km (40723 mile)
    Distance after DTC stored
    -
    Running Time from MIL ON
    Running time from MIL on/
    Min.: 0 minutes,
    Max.: 65535 minutes
    Equivalent to running time after MIL turns on
    -
    Time after DTC Cleared
    Time after DTC cleared/
    Min.: 0 minutes,
    Max.: 65535 minutes
    Equivalent to time after DTCs cleared
    -
    Distance from DTC Cleared
    Distance after DTC cleared/
    Min.: 0 km (0 mile)
    Max.: 65535 km (40723 mile)
    Equivalent to distance driven after DTCs cleared
    -
    Warmup Cycle Cleared DTC
    Warm-up cycle after DTC cleared/
    Min.: 0, Max.: 255
    Number of warm-up cycles after DTCs cleared
    -
    Engine Speed from EFI
    Engine speed/
    Min.: 0 rpm
    Max.: 16383.75 rpm
    Engine idling: 720 to 820 rpm
    Engine speed received from the ECM.
    Intake-Air Temp from EFI
    Intake air temperature/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    Equivalent to temperature at intake manifold
    Intake air temperature received from the ECM.
    Coolant Temp from EFI
    Engine coolant temperature/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    After warming up: 60 to 90°C (140 to 194°F)
    Coolant temperature received from the ECM.
    Accel Position from EFI
    Absolute accelerator pedal position/
    Min.: 0%
    Max.: 100%
    1. Accelerator pedal released: 0%
    2. Accelerator pedal fully depressed: 100%
    Accelerator position received from the ECM.
    Injection Volume from EFI
    Injection volume/
    Min.: 0 mm3/st
    Max.: 639.98 mm3/st
    Engine idling: 3.0 to 10 mm3/st
    Injection volume received from the ECM.
    SPD (NT)
    Input turbine speed (speed sensor NT)/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Lock-up on (after warming up the engine): Value from speed sensor NT equal to engine speed
    2. Lock-up off (idling with shift lever in N): Value from speed sensor NT nearly equal to engine speed
    The data is displayed in increments of 50 rpm.
    SPD (NC)
    Counter gear speed (speed sensor NC)/
    Min.: 0 rpm
    Max.: 12750 rpm
    Vehicle stopped: 0 km/h (0 mph)
    The data is displayed in increments of 50 rpm.
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in R
    2. OFF: Shift lever not in R
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in D or M
    2. OFF: Shift lever not in D or M
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    A/T Oil Temperature 1
    ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approx. 80°C (176°F)
    2. Equal to ambient temperature after cold soak
    If the value is "-40°C (-40°F)" or "150°C (302°F)", the ATF temperature sensor circuit is open or shorted.
    NT Sensor Voltage
    Input turbine speed sensor (speed sensor NT) output voltage/
    Min.: 0 V
    Max.: 5 V
    Engine idling: 0.1 to 1.9 V
    -
    NC Sensor Voltage
    Counter gear speed sensor (speed sensor NC) output voltage/
    Min.: 0 V
    Max.: 5 V
    Engine idling: 0.1 to 1.9 V
    -
    TPS 3 Switch
    No. 3 ATF pressure switch status/
    ON or OFF
    1. ON: Shift solenoid valve SLU is on
    2. OFF: Shift solenoid valve SLU is off
    -
    TPS 2 Switch
    No. 2 ATF pressure switch status/
    ON or OFF
    1. ON: Gear is 4th, 5th or 6th
    2. OFF: Gear is 1st, 2nd or 3rd
    -
    TPS 1 Switch
    No. 1 ATF pressure switch status/
    ON or OFF
    1. ON: Gear is 1st, 2nd, 3rd or 4th
    2. OFF: Gear is 5th or 6th
    -
    Lock Up
    Lock-up/
    ON or OFF
    1. ON: Lock-up operating
    2. OFF: Lock-up not operating
    -
    Lock Up Solenoid Status
    Shift solenoid valve SL status/
    ON or OFF
    1. ON: Shift solenoid valve SL operating
    2. OFF: Shift solenoid valve SL not operating
    -
    Shift Status
    TCM gearshift command/
    1st, 2nd, 3rd, 4th, 5th or 6th
    Same as actual gear
    -
    SLT Solenoid Status
    Shift solenoid valve SLT status/
    ON or OFF
    1. OFF: Accelerator pedal depressed
    2. ON: Accelerator pedal released
    -
    SLU Solenoid Status
    Shift solenoid valve SLU status/
    ON or OFF
    1. ON: Shift solenoid valve SLU operating
    2. OFF: Shift solenoid valve SLU not operating
    -

    Engine 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Pattern Switch (PWR/M)
    Pattern select switch (SPORT) status/
    ON or OFF
    1. ON: Pattern select switch (SPORT) pushed
    2. OFF: Pattern select switch (SPORT) not pushed
    -
    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Shift lever held in "+" (up-shift)
    2. OFF: Shift lever not held in "+" (up-shift)
    -
    1. ON: "+" shift paddle operated and held (up-shift)
    2. OFF: "+" shift paddle not operated (up-shift)
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Shift lever held in "-" (down-shift)
    2. OFF: Shift lever not held in "-" (down-shift)
    -
    1. ON: "-" shift paddle operated and held (down-shift)
    2. OFF: "-" shift paddle not operated (down-shift)
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    1. ON: Shift lever in M, "+" or "-"
    2. OFF: Shift lever not in M, "+" or "-"
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Active Test.

  7. According to the display on the tester, perform the Active Test.

    ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON or OFF
    1. ON: TC and TE1 are connected.
    2. OFF: TC and TE1 are disconnected.
    Activate the Solenoid (SLU)
    Operate shift solenoid valve SLU
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SLT)*
    Operate shift solenoid valve SLT and raise line pressure
    ON or OFF

    HINT:
    ON: No action (normal operation)
    OFF: Line pressure up (When Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn off).

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    Activate the Lock Up
    Control shift solenoid valve SLU and SL to set the automatic transaxle to lock-up
    ON or OFF
    Can be used to check shift solenoid valve SLU and SL operation.
    [Vehicle Condition]
    1. Vehicle speed: 60 km/h (37 mph) or more
    Activate the Solenoid (SL)
    Operate shift solenoid valve SL
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Control the Shift Position
    Operate the shift solenoid valves and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Can be used to check the operation of the shift solenoid valves.
    A 10-second interval is required between gear changes.
    Do not down-shift at high speeds. Doing so will damage the automatic transaxle.
    [Vehicle Condition]
    1. 50 km/h (30 mph) or less
    Activate the Solenoid (SL1)
    Operate shift solenoid valve SL1
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL2)
    Operate shift solenoid valve SL2
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL3)
    Operate shift solenoid valve SL3
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL4)
    Operate shift solenoid valve SL4
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N

    HINT:
    *: The "Activate the Solenoid (SLT)" Active Test is performed to confirm that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test (Click here).
    Note that the pressure readings for the Active Test and Hydraulic Test are different.