Home › TRANSMISSION · U660F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0705    Transmission Range Sensor Circuit Malfunction (PRNDL Input)

for Preparation Click here


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the TCM.

DTC Code
DTC Detection Condition
Trouble Area
P0705
Either condition is met:
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
  1. NSW input signal is on.
  2. R input signal is on.
  3. D input signal is on.
(B) NSW, R and D switches are all off simultaneously.
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. TCM

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and/or the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position (P, R or D) and sends a signal to the TCM.
For safety, the park/neutral position switch detects the shift lever position so that the engine cannot be started when the shift lever is not in P or N.
The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously, or receives no position signal at all.

WIRING DIAGRAM

Refer to DTC P0617 .

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in P or N
    2. OFF: Shift lever not in P or N
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in R
    2. OFF: Shift lever not in R
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in D or M
    2. OFF: Shift lever not in D or M
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

1.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)


    C197711E07
  1. Disconnect the park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B28-1 (RB) - Body ground
    Ignition switch ON
    11 to 14 V
    B28-1 (RB) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Park/Neutral Position Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BATTERY)
OK


2.CHECK HARNESS AND CONNECTOR (TCM OUTPUT SIGNAL)


    C197711E08
  1. Disconnect the park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B28-4 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    B28-4 (B) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Park/Neutral Position Switch)



NG
Go to step 5
OK


3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C197712E07
  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (B) - 9 (L)
    Shift lever in P
    Below 1 Ω
    1 (RB) - 2 (RL)
    Shift lever in R
    Below 1 Ω
    4 (B) - 9 (L)
    Shift lever in N
    Below 1 Ω
    1 (RB) - 7 (DL)
    Shift lever in D, M, "+" or "-"
    Below 1 Ω
    4 (B) - 9 (L)
    Shift lever not in P
    10 kΩ or higher
    1 (RB) - 2 (RL)
    Shift lever not in R
    10 kΩ or higher
    4 (B) - 9 (L)
    Shift lever not in N
    10 kΩ or higher
    1 (RB) - 7 (DL)
    Shift lever not in D, M, "+" or "-"
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Park/Neutral Position Switch)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)


    C205632E09
  1. Disconnect the TCM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B128-16 (D) - Body ground
    1. Ignition switch ON
    2. Shift lever in D
    11 to 14 V
    B128-15 (R) - Body ground
    1. Ignition switch ON
    2. Shift lever in R
    11 to 14 V*
    B128-16 (D) - Body ground
    1. Ignition switch ON
    2. Shift lever not in D
    Below 1 V
    B128-15 (R) - Body ground
    1. Ignition switch ON
    2. Shift lever not in R
    Below 1 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to TCM)

    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM (Click here)  

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)


    C205642E02
  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B28-4 (B) - B128-11 (NSW)
    Always
    Below 1 Ω
    B28-4 (B) or B128-11 (NSW) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Park/Neutral Position Switch)
    *2
    Front view of wire harness connector
    (to TCM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM (Click here)