Home › TRANSMISSION · U660F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > Transmission Control Switch Circuit

for Preparation Click here


DESCRIPTION

After moving the shift lever to M, it is possible to switch the shift range between "1" (M1 range) and "6" (M6 range) using the transmission control switch.
Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" once lowers the shift range by one.

WIRING DIAGRAM


C209057E01


INSPECTION PROCEDURE

1.INSPECT TRANSMISSION CONTROL SWITCH


    C203344E02
  1. Disconnect the transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (IG) - 7 (S)
    Shift lever in M, "+" or "-"
    Below 1 Ω
    2 (SFTU) - 5 (E)
    Shift lever held in "+" (Up-shift)
    Below 1 Ω
    1 (SFTD) - 5 (E)
    Shift lever held in "-" (Down-shift)
    Below 1 Ω
    3 (IG) - 7 (S)
    Shift lever not in M, "+" or "-"
    10 kΩ or higher
    2 (SFTU) - 5 (E)
    Shift lever in M
    10 kΩ or higher
    1 (SFTD) - 5 (E)
    Shift lever in M
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Transmission Control Switch)



NG
REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY) (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY AND BODY GROUND)


    C203343E02
  1. Disconnect the transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E98-3 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    E98-3 (IG) - Body ground
    Ignition switch off
    Below 1 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E98-5 (E) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*1
Front view of wire harness connector
(to Transmission Control Switch)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)


    C200874E11
  1. Disconnect the ECM connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A12-9 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever in M, "+" or "-"
    11 to 14 V
    A12-9 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever not in M, "+" or "-"
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B32-61 (SFTU) - Body ground
    Shift lever held in "+" (Up-shift)
    Below 1 Ω
    A12-28 (SFTD) - Body ground
    Shift lever held in "-" (Down-shift)
    Below 1 Ω
    B32-61 (SFTU) - Body ground
    Shift lever in M
    10 kΩ or higher
    A12-28 (SFTD) - Body ground
    Shift lever in M
    10 kΩ or higher

Text in Illustration 
*1
Front view of wire harness connector
(to ECM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)