Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1800/51    Short in Driver Side Squib Circuit

DTC    B1801/51    Open in Driver Side Squib Circuit

DTC    B1802/51    Short to GND in Driver Side Squib Circuit

DTC    B1803/51    Short to B+ in Driver Side Squib Circuit

for Preparation Click here


DESCRIPTION

  1. The driver side squib circuit consists of the center airbag sensor, the spiral cable and the steering pad.
  2. The circuit instructs the SRS to deploy when the deployment conditions are met.
  3. These DTCs are recorded when a malfunction is detected in the driver side squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1800/51
Center airbag sensor receives a line short signal 5 times in the driver side squib circuit during primary check.
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor
B1801/51
Center airbag sensor receives an open signal in the driver side squib circuit for 2 seconds.
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor
B1802/51
Center airbag sensor receives a short to ground signal in the driver side squib circuit for 0.5 seconds.
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor
B1803/51
Center airbag sensor receives a short to B+ signal in the driver side squib circuit for 0.5 seconds.
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor

WIRING DIAGRAM


H101253E06


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (Click here).
  2. After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK STEERING PAD (DRIVER SIDE SQUIB)
C114804E04
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the steering pad.

  1. Connect SST (resistance 2.1 Ω) to connector E.

    CAUTION:
    Never connect a tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1800, B1801, B1802, B1803 or 51 is not output.

    HINT:
    DTCs other than DTC B1800, B1801, B1802, B1803 or 51 may be output at this time, but they are not related to this check.



OK
REPLACE STEERING PAD
NG


2.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from the spiral cable.

  1. Check that the spiral cable connectors (on the steering pad side) are not damaged.

    OK:
    Lock button is not disengaged, and claw of lock is not deformed or damaged.



NG
REPLACE SPIRAL CABLE
OK


3.CHECK DRIVER SIDE SQUIB CIRCUIT


    C114805E02
  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    D+ - Body ground
    Below 1 V
    D- - Body ground
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    D+ - D-
    Below 1 Ω
    D+ - Body ground
    1 MΩ or higher
    D- - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    D+ - D-
    1 MΩ or higher



OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
NG


4.CHECK INSTRUMENT PANEL WIRE


    C114807E07
  1. Restore the released activation prevention mechanism of connector B to its original position.

  1. Disconnect the instrument panel wire connector from the spiral cable.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E11-1 (D+) - Body ground
    Below 1 V
    E11-2 (D-) - Body ground
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E11-1 (D+) - E11-2 (D-)
    Below 1 Ω
    E11-1 (D+) - Body ground
    1 MΩ or higher
    E11-2 (D-) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E11-1 (D+) - E11-2 (D-)
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE SPIRAL CABLE