Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1805/52    Short in Front Passenger Side Squib Circuit

DTC    B1806/52    Open in Front Passenger Side Squib Circuit

DTC    B1807/52    Short to GND in Front Passenger Side Squib Circuit

DTC    B1808/52    Short to B+ in Front Passenger Side Squib Circuit

for Preparation Click here


DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor and the front passenger airbag.
The circuit instructs the SRS to deploy when the deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1805/52
Center airbag sensor receives a line short signal 5 times in the front passenger side squib circuit during primary check.
  1. No. 1 instrument panel wire
  2. No. 2 instrument panel wire
  3. Front passenger airbag (Front passenger side squib)
  4. Center airbag sensor
B1806/52
Center airbag sensor receives an open circuit signal in the front passenger side squib circuit for 2 seconds.
  1. No. 1 instrument panel wire
  2. No. 2 instrument panel wire
  3. Front passenger airbag (Front passenger side squib)
  4. Center airbag sensor
B1807/52
Center airbag sensor receives a short to ground signal in the front passenger side squib circuit for 0.5 seconds.
  1. No. 1 instrument panel wire
  2. No. 2 instrument panel wire
  3. Front passenger airbag (Front passenger side squib)
  4. Center airbag sensor
B1808/52
Center airbag sensor receives a short to B+ signal in the front passenger side squib circuit for 0.5 seconds.
  1. No. 1 instrument panel wire
  2. No. 2 instrument panel wire
  3. Front passenger airbag (Front passenger side squib)
  4. Center airbag sensor

WIRING DIAGRAM


H101119E21


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (Click here).
  2. After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)


    C128693E04
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the front passenger airbag.

  1. Connect SST (resistance 2.1 Ω) to connector E.

    CAUTION:
    Never connect a tester to the front passenger airbag (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1805, B1806, B1807, B1808 or 52 is not output.

    HINT:
    DTCs other than DTC B1805, B1806, B1807, B1808 or 52 may be output at this time, but they are not related to this check.



OK
REPLACE FRONT PASSENGER AIRBAG ASSEMBLY
NG


2.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from the instrument panel wire.

  1. Check that the instrument panel wire connectors (on the front passenger side airbag) are not damaged.

    OK:
    Lock button is not disengaged, and claw of lock is not deformed or damaged.



NG
Go to step 4
OK


3.CHECK INSTRUMENT PANEL WIRE


    H100374E21
  1. Disconnect the connector from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    g1-2 (P+) - Body ground
    Below 1 V
    g1-1 (P-) - Body ground
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    g1-2 (P+) - g1-1 (P-)
    Below 1 Ω
    g1-2 (P+) - Body ground
    1 MΩ or higher
    g1-1 (P-) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    g1-2 (P+) - g1-1 (P-)
    1 MΩ or higher



OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
NG


4.CHECK NO. 2 INSTRUMENT PANEL WIRE


    C130806E12
  1. Disconnect the No. 2 instrument panel wire connector from the instrument panel wire.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    g1-2 (P+) - Body ground
    Below 1 V
    g1-1 (P-) - Body ground
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    g1-1 (P-) - Eg1-2
    Below 1 Ω
    g1-2 (P+) - Eg1-1
    Below 1 Ω
    g1-1 (P-) - g1-2 (P+)
    1 MΩ or higher
    g1-1 (P-) - Body ground
    1 MΩ or higher
    g1-2 (P+) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 2 INSTRUMENT PANEL WIRE
OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE