Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1653/35    Seat Position Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat position sensor circuit consists of the center airbag sensor and the seat position sensor.
DTC B1653/35 is recorded when a malfunction is detected in the seat position sensor circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1653/35
When one of following conditions is met:
  1. Center airbag sensor detects line short signal, open signal, short to ground signal or short to B+ signal in seat position sensor circuit for 2 seconds.
  2. Seat position sensor malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Front seat inner belt
  3. Seat position sensor
  4. Center airbag sensor

WIRING DIAGRAM


C123584E07


INSPECTION PROCEDURE

1.CHECK FOR DTC
H100890E06
  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    DTCs other than DTC B1653/35 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the seat position sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTOR
OK


3.CHECK SEAT POSITION SENSOR CIRCUIT (FOR OPEN)
C128681E05
  1. Disconnect the connectors from the center airbag sensor and the seat position sensor.

  1. Using a service wire, connect K1-14 (DSP+) and K1-13 (DSP-)*1 or L18-14 (DSP+) and L18-13 (DSP-)*2 of connector B.

    HINT:
    *1: for LHD
    *2: for RHD

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    2 (LSP+) - 1 (LSP-)
    Below 1 Ω
    for RHD:
    Tester Connection
    Specified Condition
    2 (RSP+) - 1 (RSP-)
    Below 1 Ω



NG
Go to step 10
OK


4.CHECK SEAT POSITION SENSOR CIRCUIT (FOR SHORT)
H100151E06
  1. Disconnect the service wire from connector B.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    2 (LSP+) - 1 (LSP-)
    1 MΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    2 (RSP+) - 1 (RSP-)
    1 MΩ or higher



NG
Go to step 11
OK


5.CHECK SEAT POSITION SENSOR CIRCUIT (TO B+)
H100151E04
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for LHD:
    Tester Connection
    Specified Condition
    2 (LSP+) - Body ground
    Below 1 V
    1 (LSP-) - Body ground
    Below 1 V
    for RHD:
    Tester Connection
    Specified Condition
    2 (RSP+) - Body ground
    Below 1 V
    1 (RSP-) - Body ground
    Below 1 V



NG
Go to step 12
OK


6.CHECK SEAT POSITION SENSOR CIRCUIT (TO GROUND)
H100151E04
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the voltage of the wire harness side connector.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    2 (LSP+) - Body ground
    1 MΩ or higher
    1 (LSP-) - Body ground
    1 MΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    2 (RSP+) - Body ground
    1 MΩ or higher
    1 (RSP-) - Body ground
    1 MΩ or higher



NG
Go to step 13
OK


7.CHECK SEAT POSITION SENSOR
H100890E07
  1. Connect the connectors to the center airbag sensor and the seat position sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    DTCs other than DTC B1653/35 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


8.REPLACE SEAT POSITION SENSOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the seat position sensor (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


9.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    H100890E07
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    DTCs other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END 

10.CHECK FLOOR WIRE (FOR OPEN)
C128682E03
  1. Disconnect the front seat inner belt connector from the floor wire.

  1. Using a service wire, connect K1-14 (DSP+) and K1-13 (DSP-)*1 or L18-14 (DSP+) and L18-13 (DSP-)*2 of connector B.

    HINT:
    *1: for LHD
    *2: for RHD

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    K3-2 (LSP+) - K3-1 (LSP-)
    Below 1 Ω
    for RHD:
    Tester Connection
    Specified Condition
    L16-2 (RSP+) - L16-1 (RSP-)
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY 

11.CHECK FLOOR WIRE (FOR SHORT)


    C128683E04
  1. Disconnect the front seat inner belt connector from the floor wire.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    J10-2 (LSP+) - J10-1 (LSP-)
    1 MΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    L16-2 (RSP+) - L16-1 (RSP-)
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY 

12.CHECK FLOOR WIRE (TO B+)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.



    C128683E04
  1. Disconnect the front seat inner belt connector from the floor wire.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for LHD:
    Tester Connection
    Specified Condition
    K3-2 (LSP+) - Body ground
    Below 1 V
    K3-1 (LSP-) - Body ground
    Below 1 V
    for RHD:
    Tester Connection
    Specified Condition
    L16-2 (RSP+) - Body ground
    Below 1 V
    L16-1 (RSP-) - Body ground
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY 

13.CHECK FLOOR WIRE (TO GROUND)


    C128683E04
  1. Disconnect the front seat inner belt connector from the floor wire.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    K3-2 (LSP+) - Body ground
    1 MΩ or higher
    K3-1 (LSP-) - Body ground
    1 MΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    L16-2 (RSP+) - Body ground
    1 MΩ or higher
    L16-1 (RSP-) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY