Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for DPF)

DTC    P1550    Battery Current Sensor Circuit

DTC    P1551    Battery Current Sensor Circuit Low

DTC    P1552    Battery Current Sensor Circuit High

for Preparation Click here


DESCRIPTION

The battery current sensor installed on the positive (+) battery terminal detects the amount of current supplied from the generator.
A110645E01
The battery current sensor changes current to voltage and outputs that voltage. The battery current sensor changes current at the negative (-) battery terminal to voltage and sends it to the ECM. The ECM controls the voltage of the generator based on the signals from the battery current sensor.

P1550 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
The following condition continues for 10 seconds or more with the ignition switch ON
(1 trip detection logic):
  1. Difference between the maximum and minimum current values of the battery current sensor is 1 A or less
  1. Battery current sensor
  2. Open or short in battery current sensor circuit
  3. ECM

P1551 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
Battery current sensor output value is 0.2 V or less for 0.5 seconds or more with the ignition switch ON
(1 trip detection logic)
  1. Battery current sensor
  2. Open or short in battery current sensor circuit
  3. ECM

P1552 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
Battery current sensor output value is 4.8 V or more for 0.5 seconds or higher with the ignition switch ON
(1 trip detection logic)
  1. Battery current sensor
  2. Open or short in battery current sensor circuit
  3. ECM

WIRING DIAGRAM

Refer to DTC P0516 .

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
If DTCs relating to different systems are output and they share terminal E2 as their ground, check this ground circuit first.

1.INSPECT BATTERY CURRENT SENSOR ASSEMBLY


    C129062E06
  1. Disconnect the battery current sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (VC5) - 4 (E2)
    Always
    3 to 10 kΩ
    3 (IB) - 4 (E2)
    Always
    3 to 10 kΩ
    2 (VC5) - 3 (IB)
    Always
    Below 0.5 kΩ

    Text in Illustration 
    *1
    Component without harness connected
    (Battery Current Sensor)

    HINT:
    The resistance differs according to the tester type.

  1. Reconnect the battery current sensor connector.



NG
Go to step 4
OK


2.CHECK WIRE HARNESS (BATTERY CURRENT SENSOR - ECM)
A131549E08
  1. Disconnect the battery current sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B31-2 (VC5) - B32-75 (VCIB)
    Always
    Below 1 Ω
    B31-3 (IB) - B32-116 (IB)
    Always
    Below 1 Ω
    B31-4 (E2) - E1B (B32-77)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B31-2 (VC5) or B32-75 (VCIB) - Body ground
    Always
    10 kΩ or higher
    B31-3 (IB) or B32-116 (IB) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Battery Current Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the battery current sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 5
OK


3.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 6

4.REPLACE BATTERY CURRENT SENSOR ASSEMBLY
  1. Replace the battery current sensor (Click here).



NEXT
Go to step 6

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON for 1 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END