Home › ENGINE ยท 2AD-FHV › FUEL › FUEL SUPPLY PUMP

FUEL SUPPLY PUMP > INSTALLATION

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, intake manifold or cylinder head, it is necessary to replace the fuel inlet pipe with a new one.



1. INSTALL FUEL SUPPLY PUMP ASSEMBLY


    A211306
  1. Apply a light coat of engine oil to a new O-ring.

  1. Install the O-ring to the supply pump.



    A211305
  1. Install the supply pump drive coupling.

    NOTICE:
    When reusing the coupling, it must be installed in the same orientation (top/bottom, front/back) as when it was removed.

    HINT:
    Line up the coupling with the groove in the camshaft end.



    A209096
  1. Install the supply pump with the 2 bolts.

    Torque:
    21 N*m{ 209 kgf*cm , 15 ft.*lbf }

    HINT:
    Line up the end of the supply pump drive shaft with the supply pump drive coupling.



    A213257
  1. Connect the suction control valve connector.

  1. Connect the fuel temperature sensor connector.



2. INSTALL FUEL TUBE SUB-ASSEMBLY


    A203050E02
  1. Temporarily install the fuel tube with 2 new gaskets, the check valve and union bolt.
    Text in Illustration 
    *1
    Check Valve

  1. Tighten the check valve.

    Torque:
    32 N*m{ 321 kgf*cm , 23 ft.*lbf }

  1. Tighten the union bolt.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



    A205046
  1. Insert the fuel tube connector onto the injector.



    A203842E02
  1. Turn the retainer in the direction indicated by the arrow until it makes a "click" sound.
    Text in Illustration 
    *1
    Fuel Tube Connector
    *2
    Injector
    *3
    Retainer
    *4
    O-Ring

    NOTICE:
    If the fuel tube connector is not inserted to the correct position on the injector, the retainer cannot be turned far enough in the direction of the arrow.



    A203047
  1. Connect the exhaust fuel addition injector connector.



3. INSTALL FUEL HOSE PROTECTOR


    A197570
  1. Install the fuel hose protector with the bolt.

    Torque:
    21 N*m{ 209 kgf*cm , 15 ft.*lbf }



    A206325
  1. Connect the connector.



4. INSTALL FUEL INLET PIPE SUB-ASSEMBLY


    A203057
  1. Temporarily install the fuel inlet pipe with the 2 clamps and nut.

  1. Using a 14 mm union nut wrench, first tighten the nut at the common rail end of the fuel inlet pipe.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Using a 14 mm union nut wrench, tighten the nut at the supply pump end of the fuel inlet pipe.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Tighten the No. 2 injection pipe clamp nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



5. INSTALL NO. 1 FUEL HOSE


    A114892
  1. Using pliers, grip the claws of the 2 clips and slide the 2 clips to install the No. 1 fuel hose.



6. INSTALL NO. 3 FUEL HOSE


    A205045E02
  1. Using pliers, grip the claws of the 2 clips and slide the 2 clips to install the No. 3 fuel hose.

    HINT:
    1. Push in the fuel hose so that the clearance is 2 to 3 mm (0.0787 to 0.118 in.).
    2. Position the clamp so that the distance from the end of the hose is 2 to 6 mm (0.0787 to 0.236 in.).



7. INSTALL AIR CLEANER CASE


    A208831
  1. Attach the clamp and install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



8. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


9. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Connect the air cleaner hose.



    A208843E01
  1. Attach the 3 clips to install the air cleaner cap.

  1. Connect the PCV hose.

  1. Attach the clamp and connect the mass air flow meter connector.



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


11. BLEED AIR FROM FUEL SYSTEM


    A131613
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/ sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.


    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.*1



    A194065E03
  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.


    A192848E04

    HINT:
    When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Clear the DTCs (Click here).

  1. Repeat steps *1 to *3.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

    OK:
    No DTCs are output.



12. INSPECT FOR FUEL LEAK

HINT:
Using the intelligent tester to perform Active Tests allow relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Perform Active Test.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Start the engine.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    6. Perform the Active Test.

      Tester Display
      Test Part
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurizes common rail internal fuel pressure, and checks for fuel leaks
      Stop/Start
      Performs inspection of the high pressure fuel system.
      1. Engine Speed: 2050 rpm
      2. Fuel Pressure: 172000 kPa
      3. Target Common Rail Pressure: 176000 kPa
      4. Target Pump SCV Current: 1.4 A
      5. MAP: 176 kPa
      6. MAF: 39 g/sec.



13. INSTALL NO. 1 ENGINE COVER


    A203808
  1. Attach the 4 clips to install the engine cover.



14. PERFORM INITIALIZATION
  1. Perform initialization procedure (Click here).