Home › TRANSMISSION · U660F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0798    Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3)

for Preparation Click here


DESCRIPTION

Changing from 1st to 6th is performed by the TCM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated (Click here).

DTC Code
DTC Detection Condition
Trouble Area
P0798
An open or short circuit (output signal duty is 0% or 100%) is detected by the TCM in the shift solenoid valve SL3 circuit while driving and shifting gears (SL3 output signal duty is more than 0% and less than 100% under normal conditions) (1-trip detection logic).
  1. Open or short in shift solenoid valve SL3 circuit
  2. Shift solenoid valve SL3
  3. TCM

MONITOR DESCRIPTION

The TCM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores the DTC. The TCM also performs the fail-safe function and turns the other normal shift solenoid valves on or off (in case of an open or short circuit, the TCM stops sending current to the circuit) (Click here).

WIRING DIAGRAM


C206307E04


INSPECTION PROCEDURE


HINT:
The following table shows the normal operation of shift solenoid valve SL3 when the shift lever is in D:

TCM gear shift command
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve SL3
OFF
ON
OFF
OFF
OFF
ON

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL3)


    C207057E06
  1. Remove the TCM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    16 (SL3+) - 15 (SL3-)
    20°C (68°F)
    5.0 to 5.6 Ω
    16 (SL3+) - Body ground
    Always
    10 kΩ or higher
    15 (SL3-) - Body ground
    Always
    10 kΩ or higher
    16 (SL3+) - All other terminals except 15 (SL3-)
    Always
    10 kΩ or higher
    15 (SL3-) - All other terminals except 16 (SL3+)
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without TCM connected
    (Transmission Wire)



NG
Go to step 2
OK

REPLACE TCM (Click here)  

2.INSPECT SHIFT SOLENOID VALVE SL3


    C197715E05
  1. Remove shift solenoid valve SL3.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 1
    2. Battery negative (-) → Terminal 2
    Valve moves and makes an operating noise

Text in Illustration 
*1
Component without harness connected
(Shift Solenoid Valve SL3)


NG
REPLACE SHIFT SOLENOID VALVE SL3
OK

REPLACE TRANSMISSION WIRE (Click here)