Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REMOVAL

for Preparation Click here



1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor while the engine speed is approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.

    SST
    09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)



2. DRAIN ENGINE COOLANT
For 2AD-FHV, refer to the following procedures .
For 2AD-FTV, refer to the following procedures .


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
w/ Navigation System (for HDD):
After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



4. REMOVE TUBE SUB-ASSEMBLY


    E127281E01
  1. Remove the bolt.

  1. Remove plate, as shown in the illustration.

  1. Disconnect the suction tube and liquid tube.

    NOTICE:
    1. Do not use a screwdriver or similar tool to disconnect the tube.

    2. I043960E02
      Seal the opening of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

  1. Remove the 2 O-rings from the suction tube and liquid tube.



5. DISCONNECT INLET HEATER WATER HOSE


    H102044E01
  1. Using pliers, grip the claws of the clip and slide the clip.

  1. Disconnect the heater water inlet hose.



6. DISCONNECT OUTLET HEATER WATER HOSE

HINT:
Disconnection of the heater water outlet hose is the same as for the heater water inlet hose.



7. REMOVE STEERING COLUMN ASSEMBLY
  1. Remove the steering column (Click here).



8. REMOVE UPPER INSTRUMENT PANEL
  1. Remove the upper instrument panel (Click here).



9. REMOVE LOWER INSTRUMENT PANEL
  1. Remove the lower instrument panel (Click here).



10. REMOVE DEFROSTER NOZZLE ASSEMBLY


    E124263
  1. Detach the 3 claws and remove the defroster nozzle.



11. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    E125437
  1. Fold the floor carpet back.



    E127013E02
  1. Disconnect the clamp and disconnect the wire harness.



    E124264
  1. Remove the bolt, nut, screw, and instrument panel brace.



12. REMOVE AIR DUCT REAR


    E127179
  1. Disconnect the 2 clamps and disconnect the wire harness.



    E124272
  1. Detach the 3 claws and remove the air duct rear.



13. REMOVE AIR DUCT


    E124265
  1. Detach the 2 claws and remove the air duct.



14. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY


    E127015
  1. Detach the 2 clamps.

  1. Disconnect the connector.



    E124261E01
  1. Remove the screw and air conditioning amplifier.



15. REMOVE DRAIN COOLER HOSE


    E124266
  1. Remove the drain hose.



16. REMOVE INSTRUMENT PANEL REINFORCEMENT


  1. Disconnect the 12 clamps.


    E124268E03



  1. Remove the 4 bolts and disconnect the ground wire.


    E124267



  1. Remove the 3 bolts.


    E124269



  1. Remove the 6 bolts and instrument panel reinforcement.


    E124270



17. REMOVE AIR CONDITIONING UNIT ASSEMBLY


    E127016
  1. Remove the bolt, nut and air conditioning unit.