Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for DPF)

DTC    P0031    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

DTC    P0032    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

HINT:
  1. For more information on the A/F sensor and Diesel Particulate Filter (DPF), refer to the following procedures (Click here).
  2. This DTC is related to the A/F sensor, although the caption is the oxygen sensor.

The A/F sensor outputs a voltage* that is proportional to the air-fuel ratio. The A/F sensor output voltage is used to control the A/F mixture.
The A/F sensor is located after the Diesel Particulate Filter (DPF) catalytic converter. This sensor has been developed based on the structure and technology of the A/F sensor that is used for gasoline engine. The cover for the sensor electrode has been modified to suit its application in a diesel engine. This change allows the sensor to function effectively in this DPF type diesel engine, and it also avoids problems with sensor temperature and particulate matter (PM).
In order to reduce PM, the ECM adjusts the air-fuel ratio to a value slightly richer than that which would otherwise be used (note that this mixture is still leaner than the stoichiometric air fuel ratio). The ECM controls these adjustments on signals from the A/F sensor.
When the ECM performs DPF catalyst regeneration (cleaning) by adding fuel using the exhaust fuel addition injector, the A/F sensor feedback is used to ensure that an appropriate air fuel ratio is maintained.
*: This voltage change occurs only inside the ECM. It is not possible to measure this voltage at the sensor. The intelligent tester can be used to monitor this voltage.

A212402E01

HINT:
The ECM provides a pulse width modulated control circuit to adjust current through the heater. The A/F sensor heater circuit uses a relay on the B+ side of the circuit.


A210271E02


P0031 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
  1. Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.
  2. Check that "Exhaust Temperature B1S1" displays 200°C (392°F) or higher using the intelligent tester.
A/F sensor heater current is 0.8 A or less when the heater operates for 4 seconds.
(1 trip detection logic)
  1. Open in A/F sensor heater circuit
  2. A/F sensor heater
  3. A/F relay
  4. ECM

P0032 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 5 seconds
A/F sensor heater current is 0.8 A or more when the heater does not operate for 4 seconds.
(1 trip detection logic)
  1. Short in A/F sensor heater circuit
  2. A/F sensor heater
  3. ECM

Related Data List 
DTC No.
Data List
P0031
  1. AFS Voltage B1S1
  2. AF Lambda B1S1
  3. Exhaust Temperature B1S1
P0032

MONITOR DESCRIPTION

The inner surface of the A/F sensor element is exposed to outside air. The outer surface of the sensor element is exposed to exhaust gases. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations of the exhaust and the outside air. The platinum coating amplifies the voltage generation. When heated, the sensor becomes very efficient. If the temperature of the exhaust is low without supplemental heating, the sensor will not generate useful voltage signals. The ECM controls the heating by using a duty-cycle to regulate the average current in the heater element. If the heater current is out of the normal range, the output signals of the sensor are inaccurate and the ECM cannot regulate the air-fuel ratio properly. When the heater current is out of the normal operating range, the ECM interprets this as a malfunction and stores a DTC.

WIRING DIAGRAM


A200656E02


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)


    C128155E05
  1. Disconnect the A/F sensor connector.

  1. Measure the resistance between the terminals of the A/F sensor.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HAF2) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Air Fuel Ratio Sensor)

  1. Reconnect the A/F sensor connector.



NG
Go to step 8
OK


2.CHECK TERMINAL VOLTAGE (A/F SENSOR HEATER VOLTAGE)


    C128157E03
  1. Disconnect the A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B62-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (Air Fuel Ratio Sensor)

  1. Reconnect the A/F sensor connector.



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)


    A128584E04
  1. Disconnect the A/F sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B62-1 (HAF2) - B32-104 (HAF2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B62-1 (HAF2) or B32-104 (HAF2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the A/F sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 10
OK


4.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11

5.INSPECT INTEGRATION RELAY (A/F RELAY)
  1. Inspect the integration relay (A/F relay) .



NG
Go to step 9
OK


6.CHECK HARNESS AND CONNECTOR (A/F SENSOR - A/F RELAY)


    A210066E01
  1. Disconnect the A/F sensor connector.

  1. Remove the integration relay (A/F relay) from the engine room No. 1 relay block .

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B62-2 (+B) - 1B-8
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B62-2 (+B) or 1B-8 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)
    *2
    Engine Room No. 1 Relay Block
    *3
    Front view of wire harness connector
    (to Integration Relay)

  1. Reconnect the A/F sensor connector.

  1. Reinstall the A/F relay.



NG
Go to step 10
OK


7.CHECK ECM POWER SOURCE CIRCUIT
  1. Check the ECM power source circuit (Click here).



NEXT
Go to step 11

8.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).



NEXT
Go to step 11

9.REPLACE INTEGRATION RELAY (A/F RELAY)
  1. Replace the integration relay (A/F relay) .



NEXT
Go to step 11

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace harness or connector.


NEXT


11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

    HINT:
    "Exhaust Temperature B1S1" on the intelligent tester screen should be 200°C (392°F) or higher.

  1. Confirm that the DTC is not output again.

    HINT:
    Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    2. Input DTC P0031 and/or P0032.

    3. Check that STATUS is NORMAL.

      HINT:
      1. If STATUS is NORMAL, DTC judgment is complete and the system is determined to be normal.
      2. If STATUS is INCOMPLETE or UNKNOWN, DTC judgment is incomplete. Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more again.


NEXT

END