DTC P0102 Mass or Volume Air Flow Circuit Low Input |
DTC P0103 Mass or Volume Air Flow Circuit High Input |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| After engine is started for 3 seconds | MAF meter frequency is less than 85 Hz with the engine speed at 5000 rpm or less for 3 seconds. (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| After engine is started for 3 seconds | MAF meter frequency is more than 9800 Hz with the engine speed at 5000 rpm or less for 3 seconds. (1 trip detection logic) |
|
| DTC No. | Data List |
| P0102 | MAF |
| P0103 |

| 1.INSPECT MASS AIR FLOW METER (POWER SOURCE CIRCUIT) |
![]() |
Disconnect the mass air flow meter connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B1-3 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector (to Mass Air Flow Meter) |
Reconnect the mass air flow meter connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-1 (VG) - B32-65 (VG) | Always | Below 1 Ω |
| B1-2 (E2G) - B32-64 (EVG) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B1-1 (VG) or B32-65 (VG) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Mass Air Flow Meter) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
|
| ||||
|
| ||||
| 3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ENGINE ROOM RELAY BLOCK) |
![]() |
Disconnect the mass air flow meter connector.
Remove the integration relay from the engine room No. 1 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-3 (+B) - 1A-4 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B1-3 (+B) or 1A-4 - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Mass Air Flow Meter) |
| *2 | Engine Room No. 1 Relay Block |
| *3 | Front view of wire harness connector (to Integration Relay) |
Reconnect the mass air flow meter connector.
Reinstall the integration relay.
|
| ||||
|
| ||||
| 4.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 5.CHECK ECM POWER SOURCE CIRCUIT |
Check the ECM power source circuit (Click here).
|
| ||||
| 6.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
After engine is started for 3 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0102 or P0103 | A |
| No output | B |
|
| ||||
| A | |
| 8.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Start the engine and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||