DTC P0115 Engine Coolant Temperature Circuit |
DTC P0117 Engine Coolant Temperature Circuit Low Input |
DTC P0118 Engine Coolant Temperature Circuit High Input |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 0.5 seconds | Open or short in the engine coolant temperature (ECT) sensor circuit for 0.5 seconds. (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 0.5 seconds | Short in the ECT sensor circuit for 0.5 seconds. (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 0.5 seconds | Open in the ECT sensor circuit for 0.5 seconds. (1 trip detection logic) |
|
| DTC No. | Data List |
| P0115 | Coolant Temp |
| P0117 | |
| P0118 |
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |

| 1.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value.
| Result | Proceed to |
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| 75 to 90°C (167 to 194°F) | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
![]() |
Disconnect the engine coolant temperature (ECT) sensor connector.
Connect terminals 1 and 2 of the ECT sensor wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value.
| *1 | ECT Sensor |
| *2 | ECM |
| *3 | Front view of wire harness connector (to ECT Sensor) |
Reconnect the ECT sensor connector.
|
| ||||
|
| ||||
| 3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
![]() |
Disconnect the ECT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B4-2 - B32-111 (THW) | Always | Below 1 Ω |
| B4-1 - B32-88 (ETHW) | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to ECT Sensor) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the ECT sensor connector.
Reconnect the ECM connector.
|
| ||||
|
| ||||
| 4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the ECT sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the value.
| *1 | ECT Sensor |
| *2 | ECM |
Reconnect the ECT sensor connector.
|
| ||||
|
| ||||
| 5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
![]() |
Disconnect the ECT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B4-2 or B32-111 (THW) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to ECT Sensor) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the ECT sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 6.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR. |
Replace the engine coolant temperature sensor (Click here).
|
| ||||
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM. |
Replace the ECM (Click here).
|
| ||||
| 10.REPLACE ENGINE COOLANT TEMPERATURE SENSOR |
Replace the engine coolant temperature sensor (Click here).
| NEXT | |
| 11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||