DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 3 seconds | Throttle position sensor output (VLU) is below 0.2 V for 3 seconds. (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 3 seconds | Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds. (1 trip detection logic) |
|
| DTC No. | Data List |
| P0122 | Throttle Sensor Volt % |
| P0123 |


| 1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
![]() |
Disconnect the diesel throttle body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B107-5 (VC) - B32-97 (VCVL) | Always | Below 1 Ω |
| B107-6 (VTA) - B32-119 (VLU) | Always | Below 1 Ω |
| B107-3 (E2) - B32-96 (EVLU) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B107-5 (VC) or B32-97 (VCVL) - Body ground | Always | 10 kΩ or higher |
| B107-6 (VTA) or B32-119 (VLU) - Body ground | Always | 10 kΩ or higher |
| B107-3 (E2) or B32-96 (EVLU) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Throttle Body) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the diesel throttle body assembly connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL) |
![]() |
Disconnect the diesel throttle body assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B107-5 (VC) - B7-3 (E2) | Ignition switch ON | 4.98 to 5.02 V |
| *1 | Front view of wire harness connector (to Throttle Body) |
Reconnect the diesel throttle body assembly connector.
|
| ||||
| OK | |
| 3.REPLACE DIESEL THROTTLE BODY ASSEMBLY |
Replace the diesel throttle body assembly (Click here).
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON for 3 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0122 or P0123 | A |
| No output | B |
|
| ||||
| A | |
| 5.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON for 3 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||