Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for DPF)

DTC    P0087    Fuel Rail / System Pressure - Too Low

DTC    P0190    Fuel Rail Pressure Sensor Circuit

DTC    P0192    Fuel Rail Pressure Sensor Circuit Low Input

DTC    P0193    Fuel Rail Pressure Sensor Circuit High Input

for Preparation Click here


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the internal pressure to the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs the voltage in proportion to the internal fuel pressure.

A208460E02


P0087 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
After idling for 60 seconds, repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds
Fuel pressure sensor output voltage stays at fixed value for 90 seconds.
(1 trip detection logic)
  1. Open or short in fuel pressure sensor circuit
  2. Fuel pressure sensor (common rail)
  3. Ran out of fuel
  4. Fuel frozen
  5. ECM

P0190 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or higher for 0.5 seconds.
(1 trip detection logic)
  1. Open or short in fuel pressure sensor circuit
  2. Fuel pressure sensor (common rail)
  3. ECM

HINT:
Trouble areas are related to the electrical system only (pumps are not involved)


P0192 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds.
(1 trip detection logic)
  1. Open or short in fuel pressure sensor circuit
  2. Fuel pressure sensor (common rail)
  3. ECM

HINT:
Trouble areas are related to the electrical system only (pumps are not involved)


P0193 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
Fuel pressure sensor output voltage is 4.9 V or higher for 0.5 seconds.
(1 trip detection logic)
  1. Open or short in fuel pressure sensor circuit
  2. Fuel pressure sensor (common rail)
  3. ECM

HINT:
Trouble areas are related to the electrical system only (pumps are not involved)


Related Data List 
DTC No.
Data List
P0087
  1. Fuel Press
  2. Target Common Rail Pressure
P0190
P0192
P0193

HINT:
  1. Check Fuel Press compared to Target Common Rail Pressure in the Data List by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press, Target Common Rail Pressure. Under stable conditions, the difference between Fuel Press and Target Common Rail Pressure is within +/-5000 kPa.
  2. For more information on the fuel pressure sensor and common rail system, refer to the System Description (Click here).
  3. If DTC P0087 is stored, the following symptoms may appear:
    1. Black smoke
    2. Poor drivability
    3. Lack of power
    4. Lack of power due to accelerator restriction of fail-safe function
  4. If DTC P0190, P0192 and/or P0193 is stored, the following symptoms may appear.
    1. Lack of power due to accelerator restriction of fail-safe function
  5. If DTC P0190, P0192 and/or P0193 is stored, "Fuel Press" always displays 0 kPa or 200000 kPa.


MONITOR DESCRIPTION

  1. P0087 (Fuel pressure sensor output stays at fixed value):
    1. Under normal conditions, the internal fuel pressure of the common rail usually fluctuates 1000 to 2000 kPa (10 to 20 kgf/cm2, 145 to 290 psi) even when the driving conditions are constant. This DTC is stored if there is no fluctuation of the fuel pressure. The internal fuel pressure is approximately 27000 to 37000 kPa (275 to 377 kgf/cm2, 3915 to 5365 psi) when idling, and it increases to approximately 50000 to 70000 kPa (510 to 714 kgf/cm2, 7250 to 10150 psi) when running the engine at 2500 rpm.
      If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned off.

    2. The diagram below indicates that fuel pressure rises as engine speed increases, but for the malfunction indicated by this DTC, that does not happen.


      A175676E02

  1. P0190, P0192 and P0193 (Open or short in fuel pressure sensor circuit):
    These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short malfunction of the sensor circuit.
    If these DTCs are stored, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.

WIRING DIAGRAM


A149601E13


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If DTCs relating to different systems are stored and they share terminal E2 as their ground, check this ground circuit first.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0190, P0192, P0193
    A
    P0087
    B



B
Go to step 4
A


2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)


    A204374E02
  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B60-5 (PR) - B32-66 (PCR1)
    Always
    Below 1 Ω
    B60-2 (PR2) - B32-114 (PCR2)
    Always
    Below 1 Ω
    B60-1 (VCS) - B32-69 (VCS)
    Always
    Below 1 Ω
    B60-6 (VC) - B32-68 (VCM)
    Always
    Below 1 Ω
    B60-4 (E2) - B32-67 (E2M)
    Always
    Below 1 Ω
    B60-3 (E2S) - B32-91 (E2S)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B60-5 (PR) or B32-66 (PCR1) - Body ground
    Always
    10 kΩ or higher
    B60-2 (PR2) or B32-114 (PCR2) - Body ground
    Always
    10 kΩ or higher
    B60-1 (VCS) or B32-69 (VCS) - Body ground
    Always
    10 kΩ or higher
    B60-6 (VC) or B32-68 (VCM) - Body ground
    Always
    10 kΩ or higher
    B60-4 (E2) or B32-67 (E2M) - Body ground
    Always
    10 kΩ or higher
    B60-3 (E2S) or B32-91 (E2S) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Fuel Pressure Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 8
OK


3.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
A204375E02
  1. Disconnect the fuel pressure sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B60-6 (VC) - B64-4 (E2)
    Ignition switch ON
    4.5 to 5.5 V
    B60-1 (VCS) - B64-3 (E2S)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Fuel Pressure Sensor)

  1. Reconnect the fuel pressure sensor connector.



NG
Go to step 7
OK


4.REPLACE FUEL PRESSURE SENSOR (COMMON RAIL)
  1. Replace the common rail (Click here).


NEXT


5.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0190, P0192, P0193)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Let the engine idle for 60 seconds, and then repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0087, P0190, P0192 or P0193 is output
    A
    No DTC is output
    B



B
END
A


7.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 9

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Let the engine idle for 60 seconds, and then repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds.

  1. Confirm that the DTC is not output again.

    HINT:
    Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    2. Input DTC P0087, P0190, P0192 and/or P0193.

    3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, increase the idling time.


NEXT

END