DTC P1496 Intake Air Temperature Sensor 1 Circuit Low |
DTC P1497 Intake Air Temperature Sensor 1 Circuit High |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 1 second | Short in the intake air temperature sensor (turbo) circuit for 0.5 seconds. (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 1 second | Open in the intake air temperature sensor (turbo) circuit for 0.5 seconds. (1 trip detection logic) |
|
| DTC No. | Data List |
| P1496 | Intake Air Temp (Turbo) |
| P1497 |

| 1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE [TURBO]) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
Read the value.
| Result | Proceed to |
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| OK (same as air temperature near intake manifold) | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
![]() |
Disconnect the intake air temperature sensor (turbo) connector.
Connect terminals 1 and 2 of the intake air temperature sensor (turbo) wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
Read the value.
| *1 | Intake Air Temperature Sensor (Turbo) |
| *2 | ECM |
| *3 | Front view of wire harness connector (to Intake Air Temperature Sensor (Turbo)) |
Reconnect the intake air temperature sensor (turbo) connector.
|
| ||||
|
| ||||
| 3.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM) |
![]() |
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-2 - B32-113 (THIA) | Always | Below 1 Ω |
| A49-1 - B32-90 (ETHI) | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Intake Air Temperature Sensor (Turbo)) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the intake air temperature sensor (turbo) connector.
Reconnect the ECM connector.
|
| ||||
|
| ||||
| 4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the intake air temperature sensor (turbo) connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
Read the value.
| *1 | Intake Air Temperature Sensor (Turbo) |
| *2 | ECM |
Reconnect the intake air temperature sensor (turbo) connector.
|
| ||||
|
| ||||
| 5.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM) |
![]() |
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-2 or B32-113 (THIA) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Intake Air Temperature Sensor (Turbo)) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the intake air temperature sensor (turbo) connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 6.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO). |
Replace the intake air temperature sensor (turbo) (Click here).
|
| ||||
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM. |
Replace the ECM (Click here).
|
| ||||
| 10.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO) |
Replace the intake air temperature sensor (turbo) (Click here).
| NEXT | |
| 11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||