Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for DPF)

DTC    P1271    Fuel Regulator Circuit Malfunction (EDU Drive)

DTC    P1272    Fuel Pressure Regulator Malfunction

for Preparation Click here


DESCRIPTION

The ECM controls the internal fuel pressure of the common rail by opening and closing the pressure discharge valve. When sudden deceleration occurs, the internal fuel pressure will temporarily become higher than usual and combustion noise may result. Therefore the ECM will open the valve temporarily to discharge the excess pressure inside the common rail. Also, the pressure discharge valve opens when the ignition switch is turned off to allow prompt discharge of the common rail internal pressure and so that the engine stops smoothly.

HINT:
  1. For more information on the pressure discharge valve and common rail system (Click here).
  2. For more information on the EDU (Click here).
  3. If P1271 and/or P1272 is present, refer to the DTC chart for the fuel system (Click here).


A208468E01


A205138E01


P1271 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON to off
and
Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal
When either condition below is met (1 trip detection logic):
  1. Open or short in pressure discharge valve circuit.
  2. There is no valve opening confirmation (IJf) signal from the EDU to the ECM for a specific number of times consecutively, despite the ECM sending valve opening command (PRD) signals after the engine is started
  1. Open or short in pressure discharge valve circuit
  2. Pressure discharge valve
  3. EDU

P1272 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON to off
Pressure discharge valve does not open.
Actual pressure decreasing rate deviates from the simulated pressure decreasing rate after the ignition switch is turned off.
(2 trip detection logic)
  1. Open or short in pressure discharge valve circuit (P1271 is set simultaneously)
  2. Pressure discharge valve
  3. EDU
  4. ECM

Related Data List 
DTC No.
Data List
P1271
  1. Fuel Press
  2. Target Common Rail Pressure
  3. Fuel Pressure Relief Valve
P1272

HINT:
  1. After confirming DTC P1271 and/or P1272, check the fuel pressure inside the common rail in "Powertrain / Engine and ECT / Data List / Fuel Press" using the intelligent tester.
  2. P1271:
    After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Check that P1271 is not present.
  3. P1272:
    After clearing the DTC, start and stop the engine twice (wait 30 seconds or more after turning the ignition switch off before starting the engine the second time), and then confirm that P1272 is not stored.

Reference: 
Engine Speed
Fuel Pressure (kPa)
Idling
Fuel Press is within +/-5000 kPa of Target Common Rail Pressure
2500 rpm (No engine load)

Results of real-vehicle check: 
Condition
Fuel Press (Idling)
Fuel Press (1 Second after Engine Stopped)
Pressure discharge valve normal
35000 kPa
170 kPa
Open in pressure discharge valve circuit
34000 kPa
34300 kPa


MONITOR DESCRIPTION

  1. P1271 (Open or short in pressure discharge valve circuit):
    This DTC will be set if there is no valve opening confirmation (IJf) signal sent from the EDU to the ECM, despite the ECM has commanded the EDU to open the pressure discharge valve. This DTC refers to an open or short circuit malfunction of the pressure discharge valve circuit, not a malfunction in which a valve is stuck open or closed.
    The EDU monitors the current supplied to the pressure discharge valve to verify that the current flows into the valve. If the current exceeds the specified level, the EDU interprets this as the IJf signal being low. If this DTC is stored, the ECM enters the fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned off.

    A208469E01

  1. P1272 (Closed malfunction of the pressure discharge valve):
    The pressure discharge valve will open and discharge the internal fuel pressure from the common rail to the fuel tank when the ignition switch is turned off. In this event, the ECM compares the actual drop rate of the internal fuel pressure and the target drop rate. If the ECM judges that the actual drop rate is smaller than the target, the ECM then judges that the valve is stuck closed and stores this DTC. This DTC will be stored if the internal fuel pressure does not drop to the target after the ignition switch has been turned off.
    If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned off.

MONITOR STRATEGY


P1271: 
Required sensors
EDU
Frequency of operation
Continuous
Duration
3 seconds
MIL operation
1 driving cycle

P1272: 
Required sensors
Fuel pressure sensor
Frequency of operation
Once per driving cycle
Duration
1 second
MIL operation
2 driving cycles

TYPICAL ENABLING CONDITIONS


P1271: 
Specification
The vehicle is driven at 50 km/h (31 mph) in 3rd gear, and then decelerated by complete release of the accelerator pedal 3 times.

P1272: 
Item
Specification
Minimum
Maximum
Fuel pressure
30000 kPa (306 kgf/cm2, 4350 psi)
-
Fuel temperature
0°C (32°F)
-
Battery voltage
11 V
-
The monitor will not run if the fuel pressure sensor, pressure discharge valve circuit or fuel temperature sensor is malfunctioning.

TYPICAL MALFUNCTION THRESHOLDS


P1271: 
Specification
There are no confirmation signals from the EDU for a specific number of times consecutively, despite the ECM sending command signals regularly during deceleration.

P1272: 
Specification
The internal pressure stays beyond the specified level after the ignition switch is turned off.

WIRING DIAGRAM


A209759E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. After completing repairs, confirm that P1271 and/or P1272 does not recur.
  2. If P0200 and P1271 are present simultaneously, there is an open in the INJF wire harness between the EDU and ECM, or there is an open in the wire harness for both an injector and the pressure discharge valve.
  3. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK IF DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the pending DTCs.

    Result 
    Result
    Proceed to
    P1272
    A
    P1271
    B
    P1271 and P1272
    B
    Other DTCs output
    C



B
Go to step 3

C
GO TO DTC CHART (Click here)
A


2.INSPECT COMMON RAIL ASSEMBLY
  1. Inspect the common rail assembly .



OK
Go to step 14

NG
Go to step 12

3.INSPECT PRESSURE DISCHARGE VALVE


    A204913E02
  1. Disconnect the pressure discharge valve connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Condition
    Specified Condition
    20°C (68°F)
    0.85 to 1.05 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Pressure Discharge Valve)

  1. Reconnect the pressure discharge valve connector.



NG
Go to step 12
OK


4.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - EDU)


    A204914E02
  1. Disconnect the EDU connector.

  1. Disconnect the pressure discharge valve connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B108-2 - B105-1 (RLF+)
    Always
    Below 1 Ω
    B108-1 - B105-2 (RLF-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B108-2 or B105-1 (RLF+) - Body ground
    Always
    10 kΩ or higher
    B108-1 or B105-2 (RLF-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Pressure Discharge Valve)
    *2
    Front view of wire harness connector
    (to EDU)

  1. Reconnect the EDU connector.

  1. Reconnect the pressure discharge valve connector.



NG
Go to step 9
OK


5.CHECK HARNESS AND CONNECTOR (ECM - EDU)


    A204912E05
  1. Disconnect the EDU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B104-5 (PRD) - B32-52 (PRD)
    Always
    Below 1 Ω
    B104-1 (RLF) - B32-123 (RLFF)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B104-5 (PRD) or B32-52 (PRD) - Body ground
    Always
    10 kΩ or higher
    B104-1 (RLF) or B32-123 (RLFF) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to EDU)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the EDU connector.

  1. Reconnect the ECM connector.



NG
Go to step 9
OK


6.INSPECT EDU (POWER SOURCE CIRCUIT)


    A204910E03
  1. Disconnect the EDU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B102-2 (+B) - B102-4 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Injector Driver (EDU))

  1. Reconnect the EDU connector.



NG
Go to step 10
OK


7.REPLACE EDU
  1. Replace the EDU (Click here).


NEXT


8.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272)
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the pending DTCs.

    HINT:
    1. If no pending DTCs are output, proceed to the next step to check "All Readiness".
    2. Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    2. Input DTC P1271 and P1272.

    3. Check the DTC judgment result.

      Result 
      Tester Display
      Result
      Proceed to
      Pending DTC
      P1271 and/or P1272 is output
      B
      All Readiness
      NORMAL
      A
      ABNORMAL
      B

      HINT:
      If STATUS is INCOMPLETE or UNKNOWN, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.



B
Go to step 11
A

END 

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 14

10.GO TO INJECTOR CIRCUIT
  1. Go to injector circuit (Click here).



NEXT
Go to step 14

11.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 14

12.REPLACE COMMON RAIL
  1. Replace the common rail (Click here).


NEXT


13.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the pending DTC is not output again.

    HINT:
    Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    2. Input DTC P1271 and P1272.

    3. Check the DTC judgment result.

      HINT:
      If STATUS is INCOMPLETE or UNKNOWN, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.


NEXT

END