Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

DTC    C2141/41    Transmitter ID1 Error

DTC    C2142/42    Transmitter ID2 Error

DTC    C2143/43    Transmitter ID3 Error

DTC    C2144/44    Transmitter ID4 Error

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
C2141/41
C2142/42
C2143/43
C2144/44
If an "ERROR" signal is received 3 times consecutively, tire pressure warning valve and transmitter will be judged as defective and this DTC will be output.
This will happen in situations where inflation pressure is outside range 0 to 537.5 kPa (0 to 5.27 kgf/cm2, 0 psi to 77.7 psi), temperature inside tire is outside specified range -40 to 215°C (-40 to 419 °F), or an error occurs in tire pressure warning valve and transmitter.
Tire pressure warning valve and transmitter

HINT:
It is necessary to perform the procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


INSPECTION PROCEDURE

NOTICE:
It is necessary to register an ID code after replacing the tire wheel and/or the tire pressure warning ECU and receiver (Click here).

1.IDENTIFY TRANSMITTER (CORRESPONDING TO DTC)
  1. Set the pressure of each tire to the specified value.

    Standard pressure:
    220 kPa (2.2 kgf /cm2, 32 psi)

  1. Connect the intelligent tester to the DLC3.

  1. Select "ID Tire Inflation Pressure" by following the prompts displayed on the intelligent tester.

    Tire pressure warning ECU and receiver:

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*

    HINT:
    *: It may take about 2 or 3 minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24.

  1. Rapidly release the tire pressure from any tire by 40 kPa (0.4 kgf/cm2, 5.8 psi) for 30 seconds or more.

    HINT:
    1. Identify the malfunctioning tire pressure warning valve and transmitter by rapidly releasing the pressure from each tire.
    2. Record which "ID Tire Inflation Pressure" data (ID1 to ID4) corresponds to each tire.

  1. Check the Data List.

    Result:

    Condition
    Detection Condition
    One of "ID Tire Inflation Pressure" data (ID1 to ID4) changed
    Normal
    None of "ID Tire Inflation Pressure" data changed
    Transmitter corresponding to DTC

    NOTICE:
    1. When the "ID Tire Inflation Pressure" data (IDs 1 to 4) changes, reset the tire pressure of the tires to the specified value, rotate the tires 90 to 270° and recheck.
    2. When the transmitter is normal, record the tire location and the transmitter ID.

  1. When one of the "ID Tire Inflation Pressure" data (IDs 1 to 4) changes, repeat the same procedure on the rest of the tires (one by one) to identify which tire pressure warning valve and transmitter the DTC corresponds to.

  1. When the "ID Tire Inflation Pressure" data (IDs 1 to 4) has been changed, identify the malfunctioning tire pressure warning valve and transmitter by using recorded ID numbers and the output DTC.

  1. Set the pressure of each tire to the specified value.

    Standard pressure:
    220 kPa (2.2 kgf /cm2, 32 psi)


NEXT

REPLACE TIRE WHEEL (TIRE PRESSURE WARNING VALVE AND TRANSMITTER)