Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

DTC    C2121/21    No Signal from Transmitter ID1 in Main Mode

DTC    C2122/22    No Signal from Transmitter ID2 in Main Mode

DTC    C2123/23    No Signal from Transmitter ID3 in Main Mode

DTC    C2124/24    No Signal from Transmitter ID4 in Main Mode

DTC    C2181/81    Transmitter ID1 not Received (Test Mode DTC)

DTC    C2182/82    Transmitter ID2 not Received (Test Mode DTC)

DTC    C2183/83    Transmitter ID3 not Received (Test Mode DTC)

DTC    C2184/84    Transmitter ID4 not Received (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The tire pressure warning valve and transmitter constantly sends radio waves to the tire pressure warning ECU and receiver.
Under the following conditions, the tire pressure warning antenna and receiver is unable to receiver the signals from the tire pressure warning valve and transmitter, and DTC is output.
  1. Areas facilities, or devices that use similar radio frequencies are located in the vicinity of the vehicle.
  2. Devices using similar radio frequencies are used in the vehicle.
DTCs C2121/21 to C2124/24 can only be deleted by the tester. DTCs C2181/81 to C2184/84 can be deleted when the transmitter sends a forced transmission signal or the test mode ends. DTCs C2181/81 to C2184/84 are output only in the test mode.

DTC Code
DTC Detection Condition
Trouble Area
C2121/21
C2122/22
C2123/23
C2124/24
These DTCs are detected when no signals are received for 51 minutes or more, after a vehicle speed of 5 mph (8 km/h) or more is detected and no signals are received for 12 minutes or more
  1. Tire pressure warning valve and transmitter
  1. Tire pressure monitor antenna
  1. Tire pressure warning ECU and receiver
  1. Wire harness
C2181/81
C2182/82
C2183/83
C2184/84
Malfunction in transmission / reception circuit
  1. Tire pressure warning valve and transmitter
  1. Tire pressure monitor antenna
  1. Tire pressure warning ECU and receiver
  1. Wire harness

HINT:
When no signal are received for 60 minutes or more, a DTC is output.
It is necessary to perform the procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


WIRING DIAGRAM


F101027E06


INSPECTION PROCEDURE

NOTICE:
It is necessary to register an ID code after replacing the tire wheel and/or the tire pressure warning ECU and receiver (Click here).

1.IDENTIFY TRANSMITTER (CORRESPONDING TO DTC)
  1. Set the pressure of each tire to the specified value.

    Standard pressure:
    220 kPa (2.2 kgf/cm2, 32 psi)

  1. Connect the intelligent tester to the DLC3.

  1. Select "ID Tire Inflation Pressure" by following the prompts displayed on the intelligent tester.

    Tire pressure warning ECU and receiver:

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*

    HINT:
    *: It may take about 2 or 3 minutes until the values are displayed.

  1. Rapidly release the tire pressure from any tire by 40 kPa (0.4 kgf/cm2, 5.8 psi) for 30 seconds or more.

HINT:
  1. Identify the malfunctioning tire pressure warning valve and transmitter by rapidly releasing the pressure from each tire.
  2. Record which "ID Tire Inflation Pressure" data (ID1 to ID4) corresponds to each tire.

  1. Check the Data List.

    Result:

    Condition
    Detection Condition
    One of "ID Tire Inflation Pressure" data (ID1 to ID4) changed
    Normal
    No "ID Tire Inflation Pressure" data changed
    Transmitter corresponding to DTC

    NOTICE:
    1. When the "ID Tire Inflation Pressure" data (IDs 1 to 4) changes, reset the tire pressure of the tires to the specified value, rotate the tires 90 to 270° and recheck.
    2. When the transmitter is normal, record the tire location and the transmitter ID.

  1. When one of the "ID Tire Inflation Pressure" data (IDs 1 to 4) changes, repeat the same procedure on the rest of the tires (one by one) to identify which tire pressure warning valve and transmitter the DTC corresponds to. Set the tire pressures to the appropriate specified values.

  1. Set the pressure of each tire to the specified value.

    Standard pressure:
    220 kPa (2.2 kgf/cm2, 32 psi)

  1. Check all transmitters of the tires.

    Result:
    Result
    Detection Condition
    One or more of transmitters abnormal
    All abnormal
    A
    All normal
    B



B
END
A


2.CHECK WIRE HARNESS (ECU - ANTENNA)

F101095E01

  1. Disconnect the E65 ECU connector.

  1. Disconnect the A38*1 and K24*2 antenna connector.

    HINT:
    *1: Front
    *2: Rear

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Front 
    Tester Connection
    Specified Condition
    E65-3 (ANT2) - A38-1 (ANFR)
    Below 1 Ω

    Rear:
    Tester Connection
    Specified Condition
    E65-2 (ANT1) - K24-1 (ANRL)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.READ VALUE USING INTELLIGENT TESTER (TIRE PRESSURE)
  1. Select "ID Tire Inflation Pressure" by following the prompts displayed on the intelligent tester.

    Tire pressure warning ECU and receiver:

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*

    HINT:
    *: It may take about 2 or 3 minutes until the values are displayed.

    OK:
    All tire pressure readings are equal to the actual tire pressure.



NG
REPLACE TIRE WHEEL (TIRE PRESSURE WARNING VALVE AND TRANSMITTER)
OK

END