Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

DTC    C2165/65    Abnormal Temperature Inside ID1 Tire

DTC    C2166/66    Abnormal Temperature Inside ID2 Tire

DTC    C2167/67    Abnormal Temperature Inside ID3 Tire

DTC    C2168/68    Abnormal Temperature Inside ID4 Tire

for Preparation Click here


DESCRIPTION

The tire pressure warning valve and transmitter measures tire internal temperature as well as tire pressure, and transmits the information to the tire pressure monitor antenna along with the transmitter ID. If the measured temperature is out of the specified range, the tire pressure warning ECU and receiver recognizes it as a malfunction, outputs DTCs, and blinks the tire pressure warning light.

DTC Code
DTC Detection Condition
Trouble Area
C2165/65
C2166/66
C2167/67
C2168/68
Tire internal temperature is outside -40 to 120°C (-40 to 419°F)
  1. Tire
  2. Tire pressure warning valve and transmitter

HINT:
It is necessary to perform the procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


INSPECTION PROCEDURE

NOTICE:
It is necessary to register an ID code after replacing the tire wheel and/or the tire pressure warning ECU and receiver (Click here).

1.IDENTIFY TRANSMITTER (CORRESPONDING TO DTC)
  1. Set the pressure of each tire to the specified value.

    Standard pressure:
    220 kPa (2.2 kgf/cm2, 32 psi)

  1. Connect the intelligent tester to the DLC3.

  1. Select "ID Tire Inflation Pressure" by following the prompts displayed on the intelligent tester.

    Tire pressure warning ECU and receiver:

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*

    HINT:
    *: It may take about 2 or 3 minutes until the values are displayed.

  1. Rapidly release the tire pressure from any tire by 40 kPa (0.4 kgf/cm2, 5.8 psi) for 30 seconds or more.

    HINT:
    1. Identify the malfunctioning tire pressure warning valve and transmitter by rapidly releasing the pressure from each tire.
    2. Record which "ID Tire Inflation Pressure" data (ID1 to ID4) corresponds to each tire.


    Result:

    Condition
    Detection Condition
    One of "ID Tire Inflation Pressure" data (ID1 to ID4) changed
    Normal
    No "ID Tire Inflation Pressure" data changed
    Transmitter corresponding to DTC

NOTICE:
  1. When the "ID Tire Inflation Pressure" data (IDs 1 to 4) changes, reset the tire pressure of the tires to the specified value, rotate the tires 90 to 270° and recheck.
  2. When the transmitter is normal, record the tire location and the transmitter ID.

  1. When one of the "ID Tire Inflation Pressure" data (IDs 1 to 4) changes, repeat the same procedure on the rest of the tires (one by one) to identify which tire pressure warning valve and transmitter the DTC corresponds to.

  1. When the "ID Tire Inflation Pressure" data (IDs 1 to 4) has been changed, identify the malfunctioning tire pressure warning valve and transmitter by using recorded ID numbers and the output DTC.

  1. Set the pressure of each tire to the specified value.

    Standard pressure:
    220 kPa (2.2 kgf/cm2, 32 psi)


NEXT

REPLACE TIRE WHEEL (TIRE PRESSURE WARNING VALVE AND TRANSMITTER)