DTC P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
Ignition switch ON
| The difference between VPA and VPA2 is below 0.4 V, or higher than 1.2 V for 0.5 seconds. (1 trip detection logic) |
|
| DTC No. | Data List |
| P2121 |
|
| 1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.
Read the values.
| Accelerator Pedal | Accel Sens. No.1 Volt % | Accel Sens. No.2 Volt % |
| Released | 8 to 28% | 51 to 86% |
| Depressed | 30 to 55% | 73 to 98% |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A6-1 (VCP2) - A12-57 (VCP2) | Always | Below 1 Ω |
| A6-2 (EPA2) - A12-58 (EPA2) | Always | Below 1 Ω |
| A6-3 (VPA2) - A12-54 (VPA2) | Always | Below 1 Ω |
| A6-4 (VCPA) - A12-55 (VCPA) | Always | Below 1 Ω |
| A6-5 (EPA) - A12-56 (EPA) | Always | Below 1 Ω |
| A6-6 (VPA) - A12-53 (VPA) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A6-1 (VCP2) or A12-57 (VCP2) - Body ground | Always | 10 kΩ or higher |
| A6-2 (EPA2) or A12-58 (EPA2) - Body ground | Always | 10 kΩ or higher |
| A6-3 (VPA2) or A12-54 (VPA2) - Body ground | Always | 10 kΩ or higher |
| A6-4 (VCPA) or A12-55 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A6-5 (EPA) or A12-56 (EPA) - Body ground | Always | 10 kΩ or higher |
| A6-6 (VPA) or A12-53 (VPA) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Accelerator Pedal Position Sensor) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the accelerator pedal position sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
Replace the accelerator pedal rod assembly (Click here).
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121) |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch to ON.
Fully close the accelerator pedal for 3 seconds or more, then hold it partway open for 3 seconds or more, then fully open it for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P2121 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 5.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON.
Fully close the accelerator pedal for 3 seconds, then hold it partway open for 3 seconds, then fully open it for 3 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||