DTC P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) |
DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |


| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| When either of the following conditions is met (1 trip detection logic):
| Main trouble area: Open in A/F sensor circuit
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 7 seconds | A/F sensor circuit low (bank 1 sensor 1) (1 trip detection logic) | Main trouble area: Open in A/F sensor circuit
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 7 seconds | A/F sensor circuit high (bank 1 sensor 1) (1 trip detection logic) | Main trouble area: Short in A/F sensor circuit
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 7 seconds | A/F sensor circuit low (bank 1 sensor 1) (1 trip detection logic) | Main trouble area: Open in A/F sensor circuit
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 7 seconds | A/F sensor circuit high (bank 1 sensor 1) (1 trip detection logic) | Main trouble area: Short in A/F sensor circuit
|
| DTC No. | Data List |
| P2237 |
|
| P2238 | |
| P2239 | |
| P2252 | |
| P2253 |

| 1.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the A/F sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B62-3 (AF2+) - B32-125 (AF2+) | Always | Below 1 Ω |
| B62-4 (AF2-) - B32-126 (AF2-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B62-3 (AF2+) or B32-125 (AF2+) - Body ground | Always | 10 kΩ or higher |
| B62-4 (AF2-) or B32-126 (AF2-) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to A/F Sensor) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the A/F sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 2.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Warm up the engine.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.
Confirm that the DTC is not output again.
|
| ||||
| OK | ||
| ||
| 4.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 5.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Warm up the engine.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.
Confirm that the DTC is not output again.
| NEXT | ||
| ||