DTC B1660/43 Passenger Airbag ON/OFF Indicator Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1660/43 | When one of following conditions is met:
|
|

| 1.CHECK PASSENGER AIRBAG ON / OFF INDICATOR OPERATION |
Turn the ignition switch on (IG).
Check the passenger airbag ON / OFF indicator operation.

| ON / OFF Indicator Illumination | Proceed to |
| Always ON | A |
| OFF | B |
|
| ||||
| A | |
| 2.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the front passenger seat belt warning light.
|
| ||||
| OK | |
| 3.CHECK FRONT PASSENGER AIRBAG ON/OFF INDICATOR LIGHT |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Check the passenger airbag ON / OFF indicator operation.
|
| ||||
| NG | |
| 4.CHECK INSTRUMENT PANEL WIRE (FOR OPEN) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the front passenger airbag ON / OFF indicator light.
Using a service wire, connect E49-23 (PAON) and E49-17 (P-AB) of connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| E109-6 (PAON) - E109-14 (P-AB) | Below 1 Ω |
| Tester Connection | Specified Condition |
| E108-6 (PAON) - E108-14 (P-AB) | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK INSTRUMENT PANEL WIRE (FOR SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| E49-17 (P-AB) - E49-23 (PAON) | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK INSTRUMENT PANEL WIRE (TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| E49-23 (PAON) - Body ground | Below 1 V |
| E49-17 (P-AB) - Body ground | Below 1 V |
|
| ||||
| OK | |
| 7.CHECK INSTRUMENT PANEL WIRE (TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| E49-17 (P-AB) - Body ground | 1 MΩ or higher |
| E49-23 (PAON) - Body ground | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 8.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the heater control panel*1 or clock*2.
|
| ||||
| OK | |
| 9.CHECK INSTRUMENT PANEL WIRE (FOR OPEN) |
![]() |
Disconnect the connector from the front passenger seat belt warning light.
Using a service wire, connect E49-23 (PAON) and E49-17 (P-AB) of connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| E109-6 (PAON) - E109-14 (P-AB) | Below 1 Ω |
| Tester Connection | Specified Condition |
| E108-6 (PAON) - E108-14 (P-AB) | Below 1 Ω |
|
| ||||
| OK | |
| 10.CHECK INSTRUMENT PANEL WIRE (FOR SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| E49-17 (P-AB) - E49-23 (PAON) | 1 MΩ or higher |
|
| ||||
| OK | |
| 11.CHECK INSTRUMENT PANEL WIRE (TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| E49-23 (PAON) - Body ground | Below 1 V |
| E49-17 (P-AB) - Body ground | Below 1 V |
|
| ||||
| OK | |
| 12.CHECK INSTRUMENT PANEL WIRE (TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| E49-17 (P-AB) - Body ground | 1 MΩ or higher |
| E49-23 (PAON) - Body ground | 1 MΩ or higher |
|
| ||||
| OK | |
| 13.CHECK INSTRUMENT PANEL WIRE (POWER SOURCE) |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| E109-2 (IG+) - Body ground | 10 to 14 V |
| E108-2 (IG+) - Body ground | 10 to 14 V |
|
| ||||
| OK | |
| 14.CHECK FRONT PASSENGER AIRBAG ON/OFF INDICATOR LIGHT |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the front passenger seat belt warning light.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Using a service wire, connect E109-6*1, E108-6*2 (PAON) and E109-8 (GND)*1, E108-8 (E)*2 of the heater control panel*1 or clock*2.
Using a service wire, connect E109-14*1, E108-14*2 (P-AB) and E109-8 (GND)*1, E108-8 (E)*2 of the heater control panel*1 or clock*2.
Turn the ignition switch on (IG).
Check the passenger airbag ON / OFF indicator operation.
|
| ||||
| OK | |
| 15.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Connect the connector to the center airbag sensor.
Connect the connector to the heater control panel*1 or clock*2.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||