BRAKE BOOSTER (for LHD) > INSTALLATION |
| 1. INSTALL CHECK VALVE GROMMET |
Install the grommet to the booster.
| 2. INSTALL BRAKE VACUUM CHECK VALVE ASSEMBLY |
Install the check valve to the grommet.
| 3. INSTALL BRAKE BOOSTER GASKET |
Install a new gasket to the booster.
| 4. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS |
Install the push rod clevis to the booster.
| 5. INSTALL BRAKE BOOSTER ASSEMBLY |
![]() |
Install the booster with the 4 nuts.
| 6. INSTALL PUSH ROD PIN |

Apply lithium soap base glycol grease to the push rod pin.
Install the push rod pin to the push rod clevis.
Install the clip to the push rod pin.
| 7. CHECK AND ADJUST BRAKE BOOSTER PUSH ROD |
![]() |
Set SST on the master cylinder and lower the rod of SST until it just touches the piston.
Apply chalk to the flat tip of the SST rod. Turn SST upside down and measure the clearance between the brake booster push rod and SST.
![]() |
If the clearance is not within the standard, adjust the length by holding the rod using SST and turning the tip of the rod using a 7 mm socket driver.
| 8. CONNECT VACUUM HOSE |
Connect the vacuum hose to the check valve.
| 9. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY |
Install a new O-ring to the master cylinder.
![]() |
Install the master cylinder to the booster with the 2 nuts.
![]() |
Using a union nut wrench, connect the 2 brake lines labeled C to the master cylinder.
Connect the brake fluid level warning switch connector labeled B to the master cylinder.
for Manual Transaxle:
Connect the clutch reservoir tube labeled A to the master cylinder.
| 10. INSTALL BRAKE ACTUATOR ASSEMBLY WITH BRACKET (w/o VSC) |
![]() |
Install the actuator with bracket with the 3 nuts.
![]() |
Connect the brake tube clamp to the bracket.
Connect the actuator connector.
| 11. INSTALL ABS AND TRACTION ACTUATOR ASSEMBLY WITH BRACKET (w/ VSC) |
![]() |
Install the actuator with bracket with the 3 nuts.
![]() |
Connect the brake tube clamp to the bracket.
| 12. CONNECT BRAKE LINE (w/o VSC) |
![]() |
Using a union nut wrench, connect the 6 brake lines to the correct locations on the actuator, as shown in the illustration.
| 13. CONNECT BRAKE LINE (w/ VSC) |
![]() |
Set each brake line in the correct position on the brake actuator as shown in the illustration.
![]() |
Using a union nut wrench, connect the 6 brake lines to the correct locations on the actuator, as shown in the illustration.
| 14. INSTALL AIR CLEANER BRACKET |
for 2AD-FTV:
Install the air cleaner bracket (Click here).
for 2AD-FHV:
Install the air cleaner bracket (Click here).
| 15. INSTALL COWL BODY MOUNTING REINFORCEMENT LH |
![]() |
Install the cowl body mounting reinforcement LH with the 2 nuts.
| 16. INSTALL COWL TOP PANEL OUTER SUB-ASSEMBLY |
![]() |
Install the cowl top panel outer sub-assembly with the 14 bolts.
Connect the connector.
| 17. INSTALL COWL VENTILATOR HOUSING SUB-ASSEMBLY |
![]() |
Engage the 4 clips to install the cowl ventilator housing sub-assembly.
| 18. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
Install the windshield wiper motor and link assembly (Click here).
| 19. FILL RESERVOIR WITH BRAKE FLUID |
| 20. BLEED AIR FROM BRAKE MASTER CYLINDER |
![]() |
Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.
Slowly depress and hold the brake pedal.
![]() |
Block the outer holes with your fingers, and release the pedal.
Repeat the 2 previous steps 3 or 4 times.
Using a union nut wrench, connect the 2 brake lines to the master cylinder.
| 21. BLEED AIR FROM BRAKE LINE |

Remove the bleeder plug cap.
Connect the vinyl tube to the bleeder plugs.
Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.
When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.
Repeat the 2 previous steps until all the air in the brake fluid is gone.
Tighten the bleeder plug.
Install the cap.
Bleed air from the brake line for each wheel by repeating the above procedures.
| 22. BLEED AIR FROM ABS AND TRACTION ACTUATOR ASSEMBLY (w/ VSC) |
Depress the brake pedal more than 20 times with the engine off.
Connect the intelligent tester to the DLC3, and turn the ignition switch on (IG).
Select AIR BLEEDING on the intelligent tester.
Bleed the air out of the suction line.
Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel.
Loosen the bleeder plug.
Operate the brake actuator to bleed the air using the intelligent tester.
Check if the operation has stopped by referring to the intelligent tester display.
Temporarily tighten the bleeder plug.
Repeat the 4 previous steps until all air in the fluid is completely bled out.
Tighten the bleeder plug.
Repeat all of the above procedures for the right rear wheel to bleed the air out of the suction line.
Bleed the air out of the pressure reduction line.
Connect a vinyl tube to either one of the bleeder plugs.
Loosen the bleeder plug.
Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there.
Tighten the bleeder plug, then release the brake pedal.
Repeat the 3 previous steps until all air in the fluid is completely bled out.
Tighten the bleeder plug.
Repeat all of the above procedures for the other wheels to bleed the air out of the pressure reduction line.
| 23. BLEED AIR FROM CLUTCH LINE (for Manual Transaxle) |
Fill the brake reservoir with brake fluid and bleed the clutch system (Click here).
| 24. CHECK AND ADJUST BRAKE PEDAL HEIGHT |
![]() ![]() |
Check the pedal height.
| Item | Specified Condition |
| for LHD | 184.2 to 194.2 mm (7.252 to 7.646 in.) |
| for RHD | 168.6 to 178.6 mm (6.638 to 7.031 in.) |
Adjust the pedal height.
Disconnect the connector from the stop light switch.
Remove the switch.
Loosen the push rod clevis lock nut.
Adjust the pedal height by turning the push rod.
Tighten the lock nut.
![]() |
Insert the switch into the adjuster until the switch body touches the pedal.
![]() |
Turn the switch a quarter turn clockwise.
Connect the connector to the switch.
Check the switch clearance.
| 25. CHECK BRAKE PEDAL FREE PLAY |
![]() |
Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.
Depress the pedal until resistance is felt.
Check the pedal free play by measuring the distance between the position in the previous step and the pedal released position.
Check the switch clearance.
| 26. CHECK BRAKE PEDAL RESERVE DISTANCE |
Release the parking brake lever. Start the engine.
Depress the pedal and check the pedal reserve distance.
Depress the pedal with a force of 490 N (50 kgf, 110 lbf).
Measure the distance between the pedal and dash panel.
| Item | Specified Condition | |
| for 2AD-FTV | for LHD without VSC | More than 75 mm (2.95 in.) |
| for LHD with VSC | More than 110 mm (4.33 in.) | |
| for RHD without VSC | More than 70 mm (2.75 in.) | |
| for RHD with VSC | More than 100 mm (3.93 in.) | |
| for 2AD-FHV | for LHD without VSC | More than 75 mm (2.95 in.) |
| for LHD with VSC | More than 110 mm (4.33 in.) | |
| for RHD without VSC | More than 70 mm (2.75 in.) | |
| for RHD with VSC | More than 100 mm (3.93 in.) | |
| 27. CHECK BRAKE FLUID LEVEL IN RESERVOIR |
![]() |
Check the fluid level and add fluid if necessary.
| 28. CHECK FOR BRAKE FLUID LEAKAGE |