DTC B1820/55 Short in Front Driver Side - Side Squib Circuit |
DTC B1821/55 Open in Front Driver Side - Side Squib Circuit |
DTC B1822/55 Short to GND in Front Driver Side - Side Squib Circuit |
DTC B1823/55 Short to B+ in Front Driver Side - Side Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1820/55 | Center airbag sensor receives a line short signal 5 times in the driver side - side squib circuit during primary check. |
|
| B1821/55 | Center airbag sensor receives an open signal in the driver side - side squib circuit for 2 seconds. |
|
| B1822/55 | Center airbag sensor receives a short to ground signal in the driver side - side squib circuit for 0.5 seconds. |
|
| B1823/55 | Center airbag sensor receives a short to B+ signal in the driver side - side squib circuit for 0.5 seconds. |
|

| 1.CHECK DRIVER SIDE FRONT SEAT SIDE AIRBAG ASSEMBLY (DRIVER SIDE - SIDE SQUIB) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the driver side front seat side airbag.
Connect SST (resistance 2.1 Ω) to connector E.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from the No. 1 seat airbag wire.
Check that the floor wire connectors (on the driver side - side squib) are not damaged.
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (DRIVER SIDE - SIDE SQUIB CIRCUIT) |
![]() |
Disconnect the connector from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| e1-1 (SFD+) - Body ground | Below 1 V |
| e1-2 (SFD-) - Body ground | Below 1 V |
| Tester Connection | Specified Condition |
| f1-1 (SFD+) - Body ground | Below 1 V |
| f1-2 (SFD-) - Body ground | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| e1-1 (SFD+) - e1-2 (SFD-) | Below 1 Ω |
| e1-1 (SFD+) - Body ground | 1 MΩ or higher |
| e1-2 (SFD-) - Body ground | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| f1-1 (SFD+) - f1-2 (SFD-) | Below 1 Ω |
| f1-1 (SFD+) - Body ground | 1 MΩ or higher |
| f1-2 (SFD-) - Body ground | 1 MΩ or higher |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| e1-1 (SFD+) - e1-2 (SFD-) | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| f1-1 (SFD+) - f1-2 (SFD-) | 1 MΩ or higher |
|
| ||||
| NG | |
| 4.CHECK NO. 1 SEAT AIRBAG WIRE |
![]() |
Disconnect the No. 1 seat airbag wire connector from the floor wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| e1-1 (SFD+) - Body ground | Below 1 V |
| e1-2 (SFD-) - Body ground | Below 1 V |
| Tester Connection | Specified Condition |
| f1-1 (SFD+) - Body ground | Below 1 V |
| f1-2 (SFD-) - Body ground | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| e1-1 (SFD+) - Ke1-1 | Below 1 Ω |
| e1-2 (SFD-) - Ke1-2 | Below 1 Ω |
| e1-1 (SFD+) - e1-2 (SFD-) | 1 MΩ or higher |
| e1-1 (SFD+) - Body ground | 1 MΩ or higher |
| e1-2 (SFD-) - Body ground | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| f1-1 (SFD+) - Lf1-1 | Below 1 Ω |
| f1-2 (SFD-) - Lf1-2 | Below 1 Ω |
| f1-1 (SFD+) - f1-2 (SFD-) | 1 MΩ or higher |
| f1-1 (SFD+) - Body ground | 1 MΩ or higher |
| f1-2 (SFD-) - Body ground | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||