DTC B1830/57 Short in Driver Side Curtain Shield Squib Circuit |
DTC B1831/57 Open in Driver Side Curtain Shield Squib Circuit |
DTC B1832/57 Short to GND in Driver Side Curtain Shield Squib Circuit |
DTC B1833/57 Short to B+ in Driver Side Curtain Shield Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1830/57 | Center airbag sensor receives a line short signal 5 times in the driver side curtain shield squib circuit during primary check. |
|
| B1831/57 | Center airbag sensor receives an open signal in the driver side curtain shield squib circuit for 2 seconds. |
|
| B1832/57 | Center airbag sensor receives a short to ground signal in the driver side curtain shield squib circuit for 0.5 seconds. |
|
| B1833/57 | Center airbag sensor receives a short to B+ signal in the driver side curtain shield squib circuit for 0.5 seconds. |
|

| 1.CHECK DRIVER SIDE CURTAIN SHIELD AIRBAG ASSEMBLY (DRIVER SIDE CURTAIN SHIELD SQUIB) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the driver side curtain shield airbag.
Connect SST (resistance 2.1 Ω) to connector C.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the floor wire connector (on the driver side curtain shield airbag) is not damaged.
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (DRIVER SIDE CURTAIN SHIELD SQUIB CIRCUIT) |
![]() |
Disconnect the connector from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| K14-1 (ICL+) - Body ground | Below 1 V |
| K14-2 (ICL-) - Body ground | Below 1 V |
| Tester Connection | Specified Condition |
| L9-1 (ICR+) - Body ground | Below 1 V |
| L9-2 (ICR-) - Body ground | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K14-1 (ICL+) - K14-2 (ICL-) | Below 1 Ω |
| K14-1 (ICL+) - Body ground | 1 MΩ or higher |
| K14-2 (ICL-) - Body ground | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| L9-1 (ICR+) - L9-2 (ICR-) | Below 1 Ω |
| L9-1 (ICR+) - Body ground | 1 MΩ or higher |
| L9-2 (ICR-) - Body ground | 1 MΩ or higher |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K14-1 (ICL+) - K14-2 (ICL-) | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| L9-1 (ICR+) - L9-2 (ICR-) | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||