DTC B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit |
DTC B1906/74 Open in Front Passenger Side Pretensioner Squib Circuit |
DTC B1907/74 Short to GND in Front Passenger Side Pretensioner Squib Circuit |
DTC B1908/74 Short to B+ in Front Passenger Side Front Pretensioner Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1905/74 | Center airbag sensor receives a line short signal 5 times in the front passenger side front pretensioner squib circuit during primary check. |
|
| B1906/74 | Center airbag sensor receives an open signal in the front passenger side front pretensioner squib circuit for 2 seconds. |
|
| B1907/74 | Center airbag sensor receives a short to ground signal in the front passenger side front pretensioner squib circuit for 0.5 seconds. |
|
| B1908/74 | Center airbag sensor receives a short to B+ signal in the front passenger side front pretensioner squib circuit for 0.5 seconds. |
|

| 1.CHECK FRONT PASSENGER SIDE FRONT SEAT OUTER BELT ASSEMBLY (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the front seat outer belt RH.
Connect SST (resistance 2.1 Ω) to connector C.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the floor wire connector (on the front seat outer belt RH side) is not damaged.
|
| ||||
| OK | |
| 3.CHECK NO. 2 FLOOR WIRE (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT) |
![]() |
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| L5-1 (R+) - Body ground | Below 1 V |
| L5-2 (R-) - Body ground | Below 1 V |
| Tester Connection | Specified Condition |
| K9-1 (L+) - Body ground | Below 1 V |
| K9-2 (L-) - Body ground | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| L5-1 (R+) - L5-2 (R-) | Below 1 Ω |
| L5-1 (R+) - Body ground | 1 MΩ or higher |
| L5-2 (R-) - Body ground | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| K9-1 (L+) - K9-2 (L-) | Below 1 Ω |
| K9-1 (L+) - Body ground | 1 MΩ or higher |
| K9-2 (L-) - Body ground | 1 MΩ or higher |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| L5-1 (R+) - L5-2 (R-) | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| K9-1 (L+) - K9-2 (L-) | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||