Home › ENGINE · 2AD-FHV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    U0101    Lost Communication with TCM

for Preparation Click here


DESCRIPTION

The ECM (engine control unit) communicates with the TCM (transmission control ECU) through the Controller Area Network (CAN).
If there is a problem with this communication, the ECM stores a DTC.

DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds
The following conditions are met for 1.25 seconds (1 trip detection logic):
  1. The battery voltage is 10.5 V or higher.
  2. No communication between the ECM and TCM.
  1. ECM
  2. TCM
  3. ECM to TCM circuit

WIRING DIAGRAM


C206826E02


INSPECTION PROCEDURE

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC U0101)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC U0101 is output
    A
    DTC U0101 and other DTCs are output
    B

    HINT:
    If any DTCs other than U0101 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT ECU POWER SOURCE CIRCUIT (POWER SOURCE, BODY GROUND)


    C205632E13
  1. Disconnect the TCM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B128-18 (+B) - B128-8 (E1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to TCM)

  1. Reconnect the TCM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (ECM - TCM)
  1. Disconnect the TCM connector.

  1. Disconnect the ECM connector.



    C206298E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B32-40 (CAN+) - B128-6 (CAN+)
    Always
    Below 1 Ω
    B32-63 (CAN-) - B128-7 (CAN-)
    Always
    Below 1 Ω
    B32-40 (CAN+) or B128-6 (CAN+) - Body ground or other terminals
    Always
    1 MΩ or higher
    B32-63 (CAN-) or B128-7 (CAN-) - Body ground or other terminals
    Always
    1 MΩ or higher

    *1
    Front view of wire harness connector
    (to ECM)
    *2
    Front view of wire harness connector
    (to TCM)

  1. Reconnect the TCM connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC U0101 is output
    B



B
REPLACE TCM (Click here)
A

END