LOWER INSTRUMENT PANEL > INSTALLATION |
| 1. INSTALL LOWER INSTRUMENT PANEL |
Connect the connectors, attach the clamps and install the lower instrument panel.
w/ Illumination:
Connect the connectors.
for Automatic Air Conditioning System:
Install the cooler thermistor hose and connect the connector.
Attach the claws to install the DLC3.
Install the 4 bolts, 2 screws and 2 clips.

| 2. INSTALL NO. 6 HEATER TO REGISTER DUCT ASSEMBLY (w/ Cool Box) |
![]() |
Attach the 2 claws to install the duct.
Install the 2 screws.
| 3. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Attach the 3 claws to install the hood lock control lever.
| 4. INSTALL POWER STEERING ECU ASSEMBLY |
![]() |
Install the ECU with the 3 nuts.
Connect the connectors.
| 5. INSTALL INSTRUMENT PANEL BOX |
![]() |
Attach the 6 clips to install the instrument panel box.
Install the screw.
| 6. INSTALL NO. 1 SWITCH HOLE BASE |
![]() |
Connect the connectors.
Attach the 4 clips to install the switch hole base.
| 7. INSTALL COWL SIDE TRIM BOARD RH |
| 8. INSTALL COWL SIDE TRIM BOARD LH |
![]() |
Attach the 3 claws to install the trim board.
Install the cap nut.
| 9. INSTALL FRONT DOOR SCUFF PLATE RH |
| 10. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Attach the 10 claws to install the scuff plate.
| 11. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Attach the 3 claws to install the instrument panel under cover.
| 12. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Driver Side Knee Airbag) |
![]() |
Attach the 8 claws to install the lower instrument panel finish panel.
Install the 2 screws.
| 13. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag) |
![]() |
Connect the connector.
Install the driver side knee airbag with the 4 bolts.
| 14. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Driver Side Knee Airbag) |
![]() |
Attach 3 claws to install the instrument panel under cover.
Install the 2 screws.
| 15. INSTALL REAR CONSOLE BOX SUB-ASSEMBLY |
Connect the connector.
![]() |
Install the rear console box with the 2 bolts and attach the wire harness clamp.
![]() |
Install the 2 screws.
| 16. INSTALL CONSOLE BOX CARPET |
![]() |
Install the console box carpet.
| 17. INSTALL NO. 1 INSTRUMENT PANEL BRACKET COVER INNER LH |
![]() |
Attach the 2 claws to install the instrument panel bracket cover.
| 18. INSTALL NO. 1 INSTRUMENT PANEL BRACKET COVER INNER RH |
![]() |
Attach the 2 claws to install the instrument panel bracket cover.
| 19. INSTALL CONSOLE REAR END PANEL |
![]() |
Attach the 6 claws to install the console rear end panel.
| 20. INSTALL UPPER REAR CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Connect the connector.
Attach the 4 clips to install the upper rear console panel.
| 21. INSTALL CONSOLE CUP HOLDER BOX |
![]() |
Attach the 2 clips to install the cup holder box.
Install the 2 screws.
| 22. INSTALL SWITCH BASE |
![]() |
Connect the connectors.
Attach the 2 clips and 2 claws to install the switch base.
| 23. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Attach the 2 clips and 4 claws to install the upper console panel.
| 24. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle) |
Connect the connector.
![]() |
Attach the 2 clips and 4 claws to install the floor shift position indicator housing.
| 25. INSTALL NO. 2 CONSOLE UPPER PANEL GARNISH |
![]() |
Attach the 4 clips to install the upper panel garnish.
| 26. INSTALL NO. 1 CONSOLE UPPER PANEL GARNISH |
![]() |
Attach the 4 clips to install the upper panel garnish.
| 27. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
for Manual Transaxle:
Twist the shift lever knob in the direction indicated by the arrow to install it.
![]() |
for Automatic Transaxle:
Twist the shift lever knob in the direction indicated by the arrow to install it.
| 28. INSTALL HEATER CONTROL SUB-ASSEMBLY (for Automatic Air Conditioning System) |
![]() |
Connect the connectors.
Attach the 3 clips to install the air conditioning control.
Install the 2 screws.
| 29. INSTALL HEATER CONTROL SUB-ASSEMBLY (for Manual Air Conditioning System) |
![]() |
Connect the connectors.
Attach the 3 clips to install the air conditioning control.
Install the 2 screws.
| 30. INSTALL COMBINATION SWITCH ASSEMBLY |
![]() |
Install the turn signal switch onto the steering column with the clamp.
| 31. INSTALL SPIRAL CABLE SUB-ASSEMBLY |
Check that the front wheels are facing straight ahead.
Set the turn signal switch to the neutral position.
![]() ![]() |
Install the spiral cable.
Connect the connectors to the spiral cable.
![]() |
Attach the 4 clips to the column cover (upper).
![]() |
Install the steering column cover (upper).
| 32. INSTALL STEERING COLUMN COVER |
for LHD:
Install the steering column cover .
for RHD:
Install the steering column cover .
| 33. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY |
Install the instrument panel (Click here).
| 34. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 35. CHECK SRS WARNING LIGHT |
Check the SRS warning light (Click here).