Home › TRANSMISSION · U660F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    U0100    Lost Communication with ECM / PCM "A"

for Preparation Click here


DESCRIPTION

The ECM communicates with the TCM using the Controller Area Network (CAN).
If there is a problem with this communication, the TCM stores a DTC.

DTC Code
DTC Detection Condition
Trouble Area
U0100
All conditions are met for 1.25 seconds (1-trip detection logic):
  1. Ignition switch is ON
  2. Battery voltage is 10.5 V or higher
  3. No communication between the ECM and TCM
  1. Harness and connector
  2. ECM
  3. TCM

WIRING DIAGRAM


C206835E02


INSPECTION PROCEDURE

HINT:
  1. Refer to the inspection procedure for the CAN communication system.
  2. If the CAN communication malfunctions, the TCM cannot receive current data from the ECM. In this case, the freeze frame data output from the TCM has not been updated, so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is an effective way to find malfunctions.
  3. The malfunctioning area can be confirmed using the Bus Check function of the intelligent tester (Click here).

1.CHECK TCM (POWER SOURCE, BODY GROUND)


    C205632E11
  1. Disconnect the TCM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B128-18 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B128-8 (E1) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*1
Front view of wire harness connector
(to TCM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (TCM - BATTERY, BODY GROUND)
OK


2.CHECK HARNESS AND CONNECTOR (ECM - TCM)


    C206298E03
  1. Disconnect the ECM connector.

  1. Disconnect the TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B32-40 (CAN+) - B128-6 (CAN+)
    Always
    Below 1 Ω
    B32-63 (CAN-) - B128-7 (CAN-)
    Always
    Below 1 Ω
    B32-40 (CAN+) or B128-6 (CAN+) - Body ground or other terminals
    Always
    10 kΩ or higher
    B32-63 (CAN-) or B128-7 (CAN-) - Body ground or other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)
    *2
    Front view of wire harness connector
    (to TCM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK IF DTC OUTPUT RECURS (DTC U0100)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / ECT / DTC / Clear.

  1. Replace the TCM (Click here).

    HINT:
    Replace the TCM with the TCM of a normally functioning vehicle of the same model.

  1. Start the engine.

  1. Enter the following menus: Powertrain / ECT / DTC.

  1. Read the DTCs using the intelligent tester.
    Result 
    Result
    Proceed to
    U0100 is output
    A
    DTCs are not output
    B



B
REPLACE TCM (Click here)
A

REPLACE ECM (Click here)