Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line (LHD Models)

for Preparation Click here


DESCRIPTION

When any DTC for the CAN communication system is output, first measure the resistance between the terminals of the DLC3 to specify the trouble area, and check that there is not a short in the CAN main wire, between the main wire, to +B, or to GND.

WIRING DIAGRAM


C194056E07


C194057E06


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistance of the main wire and the branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
  3. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. w/ Navigation System (for HDD):
      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or higher before disconnecting the cable from the negative (-) battery terminal.
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected.


NEXT


2.CHECK CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, CAN BUS LINES FOR SHORT CIRCUIT)


    H100769E34
  1. Measure the resistance of the DLC3.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    54 to 69 Ω
    A
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    Higher than 69 Ω
    B
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    Below 54 Ω
    C



B
CHECK CAN MAIN WIRE FOR OPEN (Click here)

C
CHECK CAN BUS LINES FOR SHORT CIRCUIT (Click here)
A


3.CHECK CAN BUS LINE FOR SHORT TO +B


    H100769E35
  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
CHECK CAN BUS LINE FOR SHORT TO +B (Click here)
OK


4.CHECK CAN BUS LINE FOR SHORT TO GND


    H100769E36
  1. Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-4 (CG)
    Ignition switch off
    200 Ω or higher
    E16-14 (CANL) - E16-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
CHECK CAN BUS LINE FOR SHORT TO GND (Click here)
OK

HOW TO PROCEED WITH TROUBLESHOOTING (Click here)