NAVIGATION SYSTEM (for DVD) > Speaker Circuit |

| 1.CHECK SPEAKER |
Check that the speakers sound.
| Result | Proceed to |
| Front No. 1 speakers do not operate | A |
| Front No. 2 speakers do not operate | B |
| Rear No. 1 speakers do not operate | C |
| All speakers do not operate | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
![]() |
Disconnect the H6*1 and/or G7*2 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (-) - 2 (TWL-) | Always | Below 1 Ω |
| 3 (+) - 4 (TWL+) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| 1 (-) - 2 (TWR-) | Always | Below 1 Ω |
| 3 (+) - 4 (TWR+) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER - FRONT NO. 2 SPEAKER) |
![]() |
Disconnect the H1*1 and/or G1*2 speaker connector.
![]() |
Disconnect the H6*1 and/or G7*2 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H1-1 - H6-3 (+) | Always | Below 1 Ω |
| H1-1 - Body ground | Always | 10 kΩ or higher |
| H1-2 - H6-1 (-) | Always | Below 1 Ω |
| H1-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| G1-1 - G7-3 (+) | Always | Below 1 Ω |
| G1-1 - Body ground | Always | 10 kΩ or higher |
| G1-2 - G7-1 (-) | Always | Below 1 Ω |
| G1-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - FRONT NO. 2 SPEAKER) |
![]() |
Disconnect the E52 navigation receiver assembly connector.
![]() |
Disconnect the H6*1 and/or G7*2 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E52-2 (FL+) - H6-4 (TWL+) | Always | Below 1 Ω |
| E52-6 (FL-) - H6-2 (TWL-) | Always | Below 1 Ω |
| E52-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| E52-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| E52-1 (FR+) - G7-4 (TWR+) | Always | Below 1 Ω |
| E52-5 (FR-) - G7-2 (TWR-) | Always | Below 1 Ω |
| E52-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| E52-5 (FR-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Temporarily replace the speaker with a new or normally functioning one (Click here).
Check that the malfunction disappears.
| Result | Proceed to |
| Malfunction does not disappear | A |
| Malfunction disappears | B |
|
| ||||
| A | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - REAR NO. 1 SPEAKER) |
![]() |
Disconnect the E53 navigation receiver assembly connector.
![]() |
Disconnect the J2*1 and/or I2*2 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E53-2 (RL+) - J2-1 | Always | Below 1 Ω |
| E53-6 (RL-) - J2-2 | Always | Below 1 Ω |
| E53-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| E53-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| E53-1 (RR+) - I2-1 | Always | Below 1 Ω |
| E53-3 (RR-) - I2-2 | Always | Below 1 Ω |
| E53-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| E53-3 (RR-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT REAR NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the J2*1 and/or I2*2 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 4 Ω |
|
| ||||
| OK | ||
| ||