ROOF HEADLINING (for Short Body) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Using a screwdriver, detach the 10 claws and remove the scuff plate.
| 3. REMOVE FRONT DOOR SCUFF PLATE RH |
| 4. REMOVE COWL SIDE TRIM BOARD LH |
![]() |
Remove the cap nut.
Using a screwdriver, detach the 3 claws and remove the trim board.
| 5. REMOVE COWL SIDE TRIM BOARD RH |
| 6. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Remove the front door opening trim weatherstrip.
| 7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
Remove the front door opening trim weatherstrip.
| 8. REMOVE FRONT PILLAR GARNISH LH |
![]() |
w/o Curtain Shield Airbag:
Using a clip remover, detach the 2 clips.
Pull the garnish in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the garnish.
![]() |
w/ Curtain Shield Airbag:
Detach the 2 clips.
Cut off the 2 clips.
Detach the 3 claws and remove the garnish.
Remove the 2 clips from the vehicle body.
![]() |
Using a clip remover, remove the 4 wiring harness clamps.
![]() |
w/ Curtain Shield Airbag:
Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.
| 9. REMOVE FRONT PILLAR GARNISH RH |
![]() |
w/o Curtain Shield Airbag:
Using a clip remover, detach the 2 clips.
Pull the garnish in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the garnish.
![]() |
w/ Curtain Shield Airbag:
Detach the 2 clips.
Cut off the 2 clips.
Detach the 3 claws and remove the garnish.
Remove the 2 clips from the vehicle body.
![]() |
Using a clip remover, remove the 4 antenna cord clamps.
![]() |
w/ Curtain Shield Airbag:
Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.
| 10. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
Install the upper instrument panel sub-assembly (Click here).
| 11. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Using a screwdriver, detach the 8 claws and remove the scuff plate.
| 12. REMOVE REAR DOOR SCUFF PLATE RH |
| 13. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
Remove the rear door opening trim weatherstrip.
| 14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH |
Remove the rear door opening trim weatherstrip.
| 15. REMOVE LOWER CENTER PILLAR GARNISH LH |
Disconnect the front seat outer belt's floor anchor.
Remove the anchor cover.
![]() |
Remove the bolt and disconnect the floor anchor.
![]() |
Using a screwdriver, detach the 2 claws.
Using a clip remover, detach the 2 clips and remove the garnish.
| 16. REMOVE LOWER CENTER PILLAR GARNISH RH |
| 17. REMOVE CENTER PILLAR GARNISH LH |
![]() |
Remove the 2 screws.
Using a clip remover, detach the clip and remove the garnish.
| 18. REMOVE CENTER PILLAR GARNISH RH |
| 19. REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY |
Remove the package tray trim pocket.
| 20. REMOVE TONNEAU COVER ASSEMBLY |
Remove tonneau cover.
| 21. REMOVE REAR FLOOR NO. 1 BOARD |
Remove the rear floor No. 1 board.
| 22. REMOVE DECK BOARD ASSEMBLY |
Remove the deck board.
| 23. REMOVE REAR FLOOR NO. 3 BOARD |
Remove the rear floor No. 3 board.
| 24. REMOVE REAR FLOOR NO. 2 BOARD |
Remove the rear floor No. 2 board.
| 25. REMOVE JACK CARRIER ASSEMBLY |
![]() |
Using a clip remover, remove the 7 clips and remove the jack carrier.
| 26. REMOVE REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE |
![]() |
Remove the 4 screws.
Using a clip remover, detach the 7 clips and remove the plate.
| 27. REMOVE BACK DOOR WEATHERSTRIP |
Remove the back door weatherstrip.
| 28. REMOVE REAR FLOOR FINISH PLATE |
![]() |
Using a clip remover, detach the 6 clips and remove the finish plate.
| 29. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH |
![]() |
Using a screwdriver, detach the 6 claws and remove the bezel.
| 30. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL RH |
![]() |
Using a screwdriver, detach the 6 claws and remove the bezel.
| 31. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER |
![]() |
Using a screwdriver, detach the 4 claws and remove the cover.
| 32. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET |
![]() |
Remove the bolt, 2 washers, collar and bracket.
| 33. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH |
![]() |
Disconnect the rear No. 1 seat belt's floor anchor.
Remove the anchor cover.
Remove the bolt and disconnect the floor anchor.
![]() |
Remove the bolt and 2 screws.
Using a screwdriver, detach the 5 claws.
Using a clip remover, detach the 5 clips and remove the trim board.
Disconnect the power outlet socket connector.
Remove the belt hanger.
| 34. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH |
![]() |
Disconnect the rear No. 1 seat belt's floor anchor.
Remove the anchor cover.
Remove the bolt and disconnect the floor anchor.
![]() |
Remove the bolt and 2 screws.
Using a screwdriver, detach the 5 claws.
Using a clip remover, detach the 5 clips and remove the trim board.
Remove the belt hanger.
| 35. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH |
![]() |
Using a clip remover, detach the 7 clips and remove the garnish.
| 36. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH |
| 37. REMOVE REAR ROOM PARTITION NET HOOK LH |
![]() |
Remove the 2 screws and net hook.
| 38. REMOVE REAR ROOM PARTITION NET HOOK RH |
| 39. REMOVE VISOR ASSEMBLY LH |
![]() |
Using a screwdriver, detach the 4 claws and remove the visor bracket cover.
![]() |
Remove portion A from the visor holder.
Detach the 2 claws and remove the visor.
| 40. REMOVE VISOR ASSEMBLY RH |
| 41. REMOVE VISOR HOLDER |
![]() |
Remove the visor holder by turning it counterclockwise.
| 42. REMOVE VANITY LIGHT ASSEMBLY |
![]() |
Using a screwdriver, pry out the vanity light assembly.
![]() |
Detach the 2 claws and vanity light.
| 43. REMOVE MAP LIGHT ASSEMBLY |
![]() |
Detach the 4 clips and remove the map light.
Disconnect the light connector.
| 44. REMOVE ROOM LIGHT ASSEMBLY |
![]() |
Using a screwdriver, detach the 4 claws and remove the 2 covers.
![]() |
Remove the bulb from the room light switch base.
![]() |
Using a screwdriver, detach the 4 claws and remove the light.
![]() |
Using a screwdriver, detach the 4 claws and remove the room light switch base.
| 45. REMOVE ASSIST GRIP COVER (for Front Grip) |
![]() |
Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.
| 46. REMOVE ASSIST GRIP SUB-ASSEMBLY |
![]() |
Detach the 4 claws and remove the assist grip.
| 47. REMOVE ASSIST GRIP COVER (for Rear Grip) |
![]() |
Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.
| 48. REMOVE REAR ASSIST GRIP ASSEMBLY |
![]() |
Detach the 4 claws and remove the assist grip.
| 49. REMOVE SHOULDER BELT ANCHOR COVER RH |
![]() |
Using a screwdriver, remove the 4 claws and cover.
| 50. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof) |
Remove the sun roof opening trim moulding.
| 51. REMOVE ROOF HEADLINING ASSEMBLY |
![]() |
Disconnect the No. 1 roof wire harness.
Using a screwdriver, remove the wire harness clamp.
Disconnect the roof wire connector.
Disconnect the antenna cord sub-assembly.
![]() |
Disconnect the antenna cord connector from the front pillar RH.
![]() |
Disconnect the 2 antenna cord connectors from the rear pillar RH.
Using a clip remover, remove the wiring harness clamp.
Remove the bracket's bolt.
![]() |
w/o Sliding Roof:
Using a clip remover, remove the 4 clips and headlining.
w/ Sliding Roof:
Disconnect the connector from the drive gear.
Using a clip remover, remove the 2 clips and headlining.
| 52. REMOVE NO. 1 ROOF WIRE |
Only when replacing the roof headlining:
Remove the double-sided tape and roof wire.
| 53. REMOVE ANTENNA CORD SUB-ASSEMBLY |
for Short Body (w/o Sliding Roof):
Apply masking tape to the antenna cord to mark it.

Remove the antenna cord from the roof headlining.
Remove the double-sided tape from the roof headlining.
for Short Body (w/ Sliding Roof):
Apply masking tape to the antenna cord to mark it.

Remove the antenna cord from the roof headlining.
Remove the double-sided tape from the roof headlining.
for Long Body (w/o Sliding Roof):
Apply masking tape to the antenna cord to mark it.

Remove the antenna cord from the roof headlining.
Remove the double-sided tape from the roof headlining.
for Long Body (w/ Sliding Roof):
Apply masking tape to the antenna cord to mark it.

Remove the antenna cord from the roof headlining.
Remove the double-sided tape from the roof headlining.
| 54. REMOVE NO. 1 ROOF SILENCER PAD (w/ Sliding Roof) |
Remove the 3 silencer pads.
| 55. REMOVE NO. 3 ROOF SILENCER PAD |
Remove the 2 silencer pads.