Home › TRANSMISSION ยท EA64 MANUAL TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY

MANUAL TRANSAXLE ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL REAR ENGINE MOUNTING BRACKET


C217401
  1. Install the mounting bracket to the transaxle with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 34 ft.*lbf }



2. INSTALL FRONT ENGINE MOUNTING BRACKET


C129225
  1. Install the mounting bracket to the transaxle with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



3. INSTALL MANUAL TRANSAXLE ASSEMBLY
  1. Align the input shaft with the clutch disc and install the transaxle to the engine.

    NOTICE:
    Make sure that the dowel pins are not loose, bent, damaged or scratched and then install the transaxle to the engine with the contact surfaces of the engine and transaxle flat against each other.



    C116719E02
  1. Install the 5 bolts.

    Torque:
    for bolt A:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }
    for bolt B:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



4. INSTALL STIFFENER PLATE RH


C127241
  1. Install the stiffener plate with the 4 bolts.

    Torque:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }



5. INSTALL STIFFENER PLATE LH


C127240
  1. Install the stiffener plate with the 4 bolts.

    Torque:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }



6. INSTALL OIL PAN INSULATOR


C127239
  1. Install the insulator with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



7. INSTALL ENGINE MOUNTING BRACKET LH


C129227
  1. Install the mounting bracket to the transaxle with the 4 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



8. INSTALL ENGINE ASSEMBLY WITH MANUAL TRANSAXLE
  1. Install the engine with manual transaxle (Click here).



9. INSTALL TRANSAXLE CONTROL CABLE ASSEMBLY


C127238E02
  1. Connect the 2 cable ends with the 2 washers and 2 clips.

  1. Install 2 new clips to the control cable bracket.



10. INSTALL NO. 1 AIR TUBE


    A208841
  1. Install the No. 1 air tube with the 2 bolts and tighten the clamp.

    Torque:
    for bolt:
    24 N*m{ 244 kgf*cm , 17 ft.*lbf }
    for clamp:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



11. INSTALL STARTER ASSEMBLY
  1. Install the starter (Click here ).



12. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY
  1. Install the starter (Click here).



13. ADD TRANSAXLE OIL
  1. Stop the vehicle in a level place.

  1. Remove the transmission filler plug and the gasket.



    D025304E21
  1. Check that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening. If the result is not as specified, add transmission oil.

    NOTICE:
    1. Too much or too little oil may cause trouble.
    2. After adjusting the oil level, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install a new gasket and the transmission filler plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



14. INSPECT TRANSAXLE OIL
  1. Stop the vehicle in a level place.

  1. Remove the transmission filler plug and the gasket.



    D025304E21
  1. Check that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening. If the result is not as specified, add transmission oil.

    NOTICE:
    1. Too much or too little oil may cause trouble.
    2. After adjusting the oil level, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install a new gasket and the transmission filler plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL