Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for HDD)

NAVIGATION SYSTEM (for HDD) > Reverse Signal Circuit

for Preparation Click here


DESCRIPTION

The navigation receiver assembly receives a reverse signal from the park/neutral position switch*1 or back-up light switch*2 and information about the navigation antenna, and then adjusts the vehicle position.
  1. *1: except Manual Transaxle
  2. *2: for Manual Transaxle

WIRING DIAGRAM


E182420E11


E182420E10


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK NAVIGATION RECEIVER ASSEMBLY (DISPLAY CHECK MODE)


    E178235E02
  1. Enter the "Failure Check/Setting" mode and select "Vehicle Signal" (Click here).

  1. Check that the display changes between ON and OFF according to the shift lever operation.

    OK:
    Shift Lever Position
    Display
    R
    ON
    Except R
    OFF

    HINT:
    This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever operation.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK NAVIGATION RECEIVER ASSEMBLY (REVERSE SIGNAL)
E146425E07
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E57-5 (REV) - Body ground
    Ignition switch ON
    Shift lever in R
    11 to 14 V
    E57-5 (REV) - Body ground
    Ignition switch ON
    Shift lever in any position except R
    Below 1 V



NG
Go to step 3
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

3.CHECK TRANSAXLE TYPE
  1. Check the transaxle type.
    Result 
    Result
    Proceed to
    Manual Transaxle
    A
    except Manual Transaxle
    B



B
Go to step 6
A


4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - BACK-UP LIGHT SWITCH)


    E179199E08
  1. Disconnect the E57 navigation receiver assembly connector.



    E182326E01
  1. Disconnect the B25 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E57-5 (REV) - B25-1
    Always
    Below 1 Ω
    E57-5 (REV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY


    E182327E01
  1. Disconnect the B25 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Shift lever in R
    Below 1 Ω
    1 - 2
    Shift lever not in R
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK
    A
    NG (for EA64F)
    B
    NG (for EA64)
    C



B
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)

C
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - PARK/NEUTRAL POSITION SWITCH)


    E179199E03
  1. Disconnect the E57 navigation receiver assembly connector.



    E179200E08
  1. Disconnect the B28 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E57-5 (REV) - B28-2 (RL)
    Always
    Below 1 Ω
    E57-5 (REV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT PARK/NEUTRAL POSITION SWITCH


    E179071E08
  1. Disconnect the B28 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (RB) - 2(RL)
    Shift lever in R
    Below 1 Ω
    1 (RB) - 2(RL)
    Shift lever in P
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)