Home › TRANSMISSION · U660F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P2810    Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4)

for Preparation Click here


DESCRIPTION

Changing from 1st to 6th is performed by the TCM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated (Click here).

DTC Code
DTC Detection Condition
Trouble Area
P2810
An open or short circuit (output signal duty is 0% or 100%) is detected by the TCM in the shift solenoid valve SL4 circuit while driving and shifting gears (SL4 output signal duty is more than 0% and less than 100% under normal conditions) (1-trip detection logic).
  1. Open or short in shift solenoid valve SL4 circuit
  2. Shift solenoid valve SL4
  3. TCM

MONITOR DESCRIPTION

The TCM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores the DTC. The TCM also performs the fail-safe function and turns the other normal shift solenoid valves on or off (in case of an open or short circuit, the TCM stops sending current to the circuit) (Click here).

WIRING DIAGRAM


C206307E07


INSPECTION PROCEDURE


HINT:
The following table shows the normal operation of shift solenoid valve SL4 when the shift lever is in D:

TCM gear shift command
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve SL4
OFF
OFF
ON
OFF
ON
OFF

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL4)


    C207057E14
  1. Remove the TCM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    22 (SL4+) - 21 (SL4-)
    20°C (68°F)
    5.0 to 5.6 Ω
    22 (SL4+) - Body ground
    Always
    10 kΩ or higher
    21 (SL4-) - Body ground
    Always
    10 kΩ or higher
    22 (SL4+) - All other terminals except 21 (SL4-)
    Always
    10 kΩ or higher
    21 (SL4-) - All other terminals except 22 (SL4+)
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without TCM connected
    (Transmission Wire)



NG
Go to step 2
OK

REPLACE TCM (Click here)  

2.INSPECT SHIFT SOLENOID VALVE SL4


    C197715E05
  1. Remove shift solenoid valve SL4.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 1
    2. Battery negative (-) → Terminal 2
    Valve moves and makes an operating noise

Text in Illustration 
*1
Component without harness connected
(Shift Solenoid Valve SL4)


NG
REPLACE SHIFT SOLENOID VALVE SL4
OK

REPLACE TRANSMISSION WIRE (Click here)