NAVIGATION ANTENNA > INSTALLATION |
| 1. INSTALL NAVIGATION ANTENNA ASSEMBLY |
![]() |
Install the navigation antenna with the 2 screws.
| 2. INSTALL NO. 3 HEATER TO REGISTER DUCT |
![]() |
Install the duct with the 2 screws.
| 3. INSTALL NO. 2 HEATER TO REGISTER DUCT |
![]() |
Install the duct with the screw.
| 4. INSTALL NO. 1 HEATER TO REGISTER DUCT |
![]() |
Install the duct with the screw.
| 5. INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT |
![]() |
Install the duct with the 3 screws.
| 6. INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT |
![]() |
Install the duct with the 3 screws.
| 7. INSTALL UPPER INSTRUMENT PANEL |
Attach the 6 clips and 5 claws to install the instrument panel.
Connect the connector and attach the clamp.
Install the 2 bolts and 2 screws.
Connect the passenger airbag connector.

![]() |
Install the 2 bolts to the passenger airbag.
| 8. INSTALL FRONT PILLAR GARNISH RH |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
Install the 4 antenna cord clamps.
![]() |
w/ Curtain Shield Airbag:
Install 2 new clips to the front pillar garnish.
Attach the 3 claws and 2 clips to install the garnish.
w/o Curtain Shield Airbag:
![]() |
Attach the 2 clips and 2 claws to install the garnish.
| 9. INSTALL FRONT PILLAR GARNISH LH |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
Install the 4 wire harness clamps.
![]() |
w/ Curtain Shield Airbag:
Install 2 new clips to the front pillar garnish.
Attach the 3 claws and 2 clips to install the garnish.
w/o Curtain Shield Airbag:
![]() |
Attach the 2 clips and 2 claws to install the garnish.
| 10. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Attach the 2 hinges to install the door.
![]() |
Attach the claw to the glove compartment door stopper.
While pushing in the sides of the glove compartment door in the direction indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.
| 11. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Attach the 5 clips to install the instrument panel register.
| 12. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET |
for HDD:
Install the navigation receiver assembly with bracket (Click here).
for DVD:
Install the navigation receiver assembly with bracket (Click here).
| 13. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL CENTER |
![]() |
Connect the connector.
Attach the 3 clips and 2 claws to install the cluster finish panel.
| 14. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL CENTER |
![]() |
Connect the connector.
Attach the 3 clips and 2 claws to install the cluster finish panel.
| 15. INSTALL COMBINATION METER ASSEMBLY |
![]() |
Connect the connector.
Attach the 2 clips to install the combination meter.
Install the 2 screws.
| 16. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Attach the 4 clips and 6 claws to install the instrument cluster finish panel.
| 17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |