CAMSHAFT > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE ENGINE ASSEMBLY |
Remove the engine assembly (Click here).
| 3. DISCONNECT ENGINE WIRE |
Disconnect the connectors and clamps securing the engine wire to the engine, remove the bracket bolts and disconnect the engine wire from the engine.
| 4. REMOVE GENERATOR ASSEMBLY |
![]() |
Remove the 3 bolts and generator.
| 5. REMOVE VACUUM PUMP ASSEMBLY |
![]() |
Disconnect the vacuum hose.
Remove the 3 bolts and vacuum pump.
Remove the 2 O-rings from the vacuum pump.
| 6. REMOVE IDLER PULLEY COVER PLATE |
![]() |
Using a screwdriver, remove the idler pulley cover plate.
| *1 | Tape |
| 7. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Remove the bolt and No. 1 idler pulley.
| 8. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Remove the bolt, No. 2 idler pulley cover plate and No. 2 idler pulley.
| *1 | No. 2 Idler Pulley Cover Plate |
| *2 | No. 2 Idler Pulley |
| 9. REMOVE NO. 4 WATER BY-PASS PIPE |
![]() |
Remove the bolt and No. 4 water by-pass pipe from the water inlet housing.
Remove the O-ring from the No. 4 water by-pass pipe.
| 10. REMOVE ENGINE MOUNTING BRACKET |
![]() |
Remove the 4 bolts, 2 nuts and engine mounting bracket.
| 11. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 3 bolts and V-ribbed belt tensioner.
| 12. REMOVE DIESEL THROTTLE BODY ASSEMBLY |
![]() |
Disconnect the No. 6 and No. 7 water by-pass hoses.
| *1 | No. 6 Water By-pass Hose |
| *2 | No. 7 Water By-pass Hose |
![]() |
Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.
| 13. REMOVE NO. 7 WATER BY-PASS HOSE |
![]() |
| 14. DISCONNECT NO. 8 WATER BY-PASS HOSE |
![]() |
| 15. REMOVE EGR VALVE BRACKET |
![]() |
Remove the 3 bolts and EGR valve bracket.
| 16. REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY |
![]() |
Disconnect the electric EGR control valve connector.
![]() |
Remove the 3 bolts, 2 nuts, No. 2 EGR pipe and 2 gaskets.
| *1 | Nut |
| 17. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY |
![]() |
Remove the electric EGR control valve and gasket.
| 18. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE |
Remove the engine oil level dipstick.
![]() |
Remove the 2 bolts and engine oil level dipstick guide.
Remove the O-ring from the engine oil level dipstick guide.
| 19. REMOVE FUEL INLET PIPE SUB-ASSEMBLY |
![]() |
Remove the nut and 2 clamps.
Using a 14 mm union nut wrench, remove the fuel inlet pipe.
| 20. REMOVE INJECTION PIPE SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and 4 injection pipe clamps.
Using a 14 mm union nut wrench, loosen the 4 nuts at the common rail end of the injection pipes.
Using a 14 mm union nut wrench, loosen the 4 nuts at the injector end of the injection pipes.
Remove the 4 injection pipes.
| 21. REMOVE NO. 4 FUEL HOSE |
![]() |
| 22. REMOVE COMMON RAIL ASSEMBLY |
![]() |
Remove the 2 bolts and common rail.
| 23. REMOVE INTAKE MANIFOLD INSULATOR |
![]() |
Remove the intake manifold insulator from the intake manifold.
| 24. REMOVE DIESEL TURBO PRESSURE SENSOR |
![]() |
Disconnect the vacuum hose.
Remove the bolt and sensor.
| 25. REMOVE NO. 1 GAS FILTER |
![]() |
Disconnect the vacuum hose.
Remove the No. 1 gas filter from the gas filter bracket.
| 26. REMOVE GAS FILTER BRACKET |
![]() |
Remove the 2 bolts and gas filter bracket.
| 27. REMOVE ENGINE COVER BRACKET |
![]() |
Remove the bolt and engine cover bracket.
| 28. REMOVE NO. 2 INTAKE MANIFOLD |
![]() |
Remove the bolt, 2 nuts, No. 2 intake manifold and gasket.
| 29. REMOVE INTAKE MANIFOLD |
![]() |
Remove the 7 bolts, 2 nuts, intake manifold and gasket.
| *1 | Nut |
| 30. REMOVE NO. 1 WATER BY-PASS HOSE |
![]() |
| 31. REMOVE OIL COOLER ASSEMBLY |
![]() |
Remove the 5 bolts and oil cooler.
Remove the 3 O-rings from the oil cooler bracket.
| 32. REMOVE NO. 6 WATER BY-PASS HOSE |
![]() |
Remove the No. 6 water by-pass hose.
| 33. REMOVE NO. 8 WATER BY-PASS HOSE |
![]() |
Remove the No. 8 water by-pass hose.
| 34. REMOVE NO. 3 WATER BY-PASS PIPE |
![]() |
Remove the 2 bolts and No. 3 water by-pass pipe.
Remove the O-ring from the No. 3 water by-pass pipe.
| 35. REMOVE NO. 1 TURBO OIL PIPE |
![]() |
Remove the 2 union bolts, 2 gaskets and No. 1 turbo oil pipe.
| 36. REMOVE NO. 1 OIL COOLER BRACKET |
![]() |
Remove the 6 bolts, nut and No. 1 oil cooler bracket.
| *1 | Nut |
Remove the 3 O-rings from the No. 1 oil cooler bracket.
| 37. REMOVE NO. 1 CYLINDER BLOCK INSULATOR |
![]() |
Remove the No. 1 cylinder block insulator from the cylinder block.
| 38. REMOVE NO. 2 WATER BY-PASS PIPE |
![]() |
Remove the 2 bolts and No. 2 water by-pass pipe from the water inlet housing.
| 39. REMOVE NO. 4 WATER BY-PASS HOSE |
![]() |
Remove the No. 4 water by-pass hose.
| 40. REMOVE WATER INLET HOUSING |
![]() |
Remove the 3 nuts and water inlet housing.
Remove the gasket from the water inlet housing.
| 41. REMOVE FUEL HOSE PROTECTOR |
![]() |
Disconnect the connector.
![]() |
Remove the bolt and fuel hose protector.
| 42. REMOVE FUEL TUBE SUB-ASSEMBLY |
![]() |
Disconnect the exhaust fuel addition injector connector.
![]() |
Turn the retainer as shown in the illustration.
![]() |
Disconnect the fuel tube from the exhaust fuel addition injector.
![]() |
Remove the check valve and gasket.
| *1 | Check Valve |
Remove the union bolt, gasket and fuel tube.
| 43. REMOVE NO. 3 FUEL HOSE |
![]() |
Remove the No. 3 fuel hose.
| 44. REMOVE NO. 2 NOZZLE LEAKAGE PIPE |
![]() |
Remove the check valve and gasket.
| *1 | Check Valve |
Remove the bolt and No. 2 nozzle leakage pipe.
| 45. REMOVE NO. 1 NOZZLE LEAKAGE PIPE |
![]() |
Remove the 4 union bolts and 4 gaskets.
Remove the bolt and No. 1 nozzle leakage pipe.
| 46. REMOVE NO. 1 NOZZLE HOLDER CLAMP |
![]() |
Remove the 4 bolts, 4 washers and 4 nozzle holder clamps.
| 47. REMOVE INJECTOR ASSEMBLY |
Remove the 4 injectors and 4 injection nozzle seats from the cylinder head.
Remove the O-ring from each injector.
| 48. REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY |
![]() |
Disconnect the 2 vacuum hoses.
Remove the bolt and No. 1 vacuum transmitting pipe.
| 49. REMOVE VACUUM SWITCHING VALVE BRACKET |
![]() |
Disconnect the 2 vacuum hoses.
Remove the 5 bolts and vacuum switching valve bracket.
| 50. REMOVE PCV HOSE |
![]() |
Remove the PCV hose.
| 51. REMOVE OIL FILLER CAP SUB-ASSEMBLY |
| 52. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 4 nozzle holder clamp seats, 14 bolts, nut and cylinder head cover.
| *1 | Bolt |
| *2 | Nozzle Holder Clamp Seat |
| *3 | Nut |
![]() |
Remove the cylinder head cover gasket and No. 2 cylinder head cover gasket from the cylinder head cover.
| *1 | Cylinder Head Cover Gasket |
| *2 | No. 2 Cylinder Head Cover Gasket |
| 53. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 18 bolts and 2 nuts.
| *1 | Nut |
![]() |
Insert the blade of an oil pan seal cutter between the oil pan and cylinder block, cut through the applied sealer and remove the oil pan.
| 54. REMOVE OIL FILTER ELEMENT |
![]() |
Connect a hose with an inside diameter of 15 mm (0.591 in.) to the oil filter drain pipe.
| *1 | Oil Filter Drain Pipe |
| *2 | Hose |
Remove the clip and open the oil filter element service cover.
![]() |
Remove the oil filter drain plug.
Remove the O-ring from the oil filter drain plug and install it to an oil filter drain pipe.
![]() |
Install the oil filter drain pipe to the oil filter cap and drain the engine oil.
| *1 | Oil Filter Cap |
| *2 | O-Ring |
| *3 | Oil Filter Drain Pipe |
Remove the oil filter drain pipe.
Apply a light coat of engine oil to a new O-ring and install it to the oil filter drain plug.
![]() |
Install the oil filter drain plug to the oil filter cap.
![]() |
Using SST, remove the oil filter cap.
![]() |
Remove the oil filter element and O-ring from the oil filter cap.
| *1 | Oil Filter Element |
| *2 | O-Ring |
| 55. REMOVE OIL FILTER BRACKET |
![]() |
Remove the 4 bolts and oil filter bracket.
![]() |
Remove the gasket from the oil filter bracket.
| 56. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the 3 bolts and oil strainer.
Remove the O-ring from the oil strainer.
| 57. REMOVE CAMSHAFT POSITION SENSOR |
![]() |
Remove the bolt and sensor.
| 58. DISCONNECT CRANKSHAFT POSITION SENSOR WIRE HARNESS |
![]() |
Using a clip remover, remove the clip.
Remove the bolt and disconnect the sensor wire harness.
| 59. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the 7 bolts, water pump and gasket.
| 60. REMOVE CRANKSHAFT PULLEY |
Set the No. 1 piston to TDC/compression.
![]() |
Turn the crankshaft pulley clockwise to align the timing mark on the pulley with the timing pointer of the timing chain cover.
| *1 | Timing Pointer |
| *2 | Timing Mark |
![]() |
Make sure that the timing mark of the camshaft timing sprocket is at the top.
| *1 | Matchmark |
| *2 | Timing Mark |
Put a matchmark on the timing chain plate that is aligned with the timing mark of the camshaft timing sprocket.
![]() |
Turn the crankshaft by approximately 90° in the engine revolution direction from the point where the No. 1 piston is set to the TDC/compression so that the lifted valve and piston do not contact each other when removing the camshaft.
![]() |
Using SST, hold the crankshaft pulley and loosen the pulley bolt.
![]() |
Using SST, remove the pulley bolt and crankshaft pulley.
| 61. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 13 bolts and seal washer.
| *1 | Bolt and Seal Washer |
![]() |
Remove the timing chain cover by prying between the timing chain cover and cylinder head, camshaft housing, cylinder block and stiffening crankcase with a screwdriver as shown in the illustration.
![]() |
Remove the gasket and O-ring from the timing chain cover.
| *1 | Gasket |
| *2 | O-Ring |
| 62. REMOVE SUPPLY PUMP ASSEMBLY |
![]() |
Remove the 2 bolts, supply pump and No. 1 supply pump drive coupling.
Remove the O-ring from the supply pump.
| 63. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner.
| *1 | Plunger |
| *2 | Stopper Plate |
Move the stopper plate downward to set the lock, and insert SST into the stopper plate hole.
![]() |
Remove the 2 bolts and No. 1 chain tensioner.
| 64. REMOVE CHAIN TENSIONER SLIPPER |
![]() |
| 65. REMOVE NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Remove the 2 bolts and No. 1 chain vibration damper.
| 66. REMOVE CAMSHAFT TIMING SPROCKET |
![]() |
Remove the 4 bolts from the sprocket while holding the hexagonal portion of the No. 2 camshaft with a wrench.
Remove the camshaft timing sprocket and chain.
| 67. REMOVE OIL PUMP DRIVE GEAR |
![]() |
Remove the oil pump drive gear from the crankshaft.
| 68. REMOVE CRANKSHAFT TIMING SPROCKET |
![]() |
Remove the crankshaft timing sprocket.
| 69. REMOVE CAMSHAFT |
![]() |
Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.
![]() |
Remove the 2 union bolts.
| *1 | Union Bolt |
| *2 | No. 4 Bearing Cap |
Uniformly loosen the 20 bearing cap bolts in several steps in the sequence shown in the illustration and remove the bolts.
Remove the 8 bearing caps, No. 1 bearing cap and 2 oil delivery pipes.
Remove the camshaft and No. 2 camshaft.
![]() |
Remove the No. 2 bearing cap.
| 70. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
![]() |
Remove the 16 valve rocker arms.
| 71. REMOVE VALVE LASH ADJUSTER ASSEMBLY |
![]() |
Remove the 16 valve lash adjusters from the cylinder head.