DTC P011C Charge Air Temperature/Intake Air Temperature Correlation (Bank 1) |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| After engine completely warmed up, allow engine to soak for long time (8 hours or more). Start the engine and idle the engine for 3 minutes or more. | After the engine is completely warmed up and then allowed to soak for a long time (8 hours or more), the difference in temperature at the intake air temperature sensor and intake air temperature sensor (turbo) after turbocharger after idling for 3 minutes is 15°C (59°F) or higher. (2 trip detection logic) |
|
| DTC No. | Data List |
| P011C |
|
| 1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P011C) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P011C is output | A |
| P011C and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE) |
Allow the engine to soak for 1 to 2 hours.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.
Read the value.
| NEXT | |
| 3.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value.
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE [TURBO]) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
Read the value.
|
| ||||
| OK | |
| 5.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-4 (THA) - B32-110 (THA) | Always | Below 1 Ω |
| B1-5 (E2) - B32-87 (ETHA) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B1-4 (THA) or B32-110 (THA) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to MAF Meter) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 7.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
|
| ||||
| 8.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM) |
![]() |
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-2 - B32-113 (THIA) | Always | Below 1 Ω |
| A49-1 - B32-90 (ETHI) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A49-2 or B32-113 (THIA) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Intake Air Temperature Sensor (Turbo)) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the intake air temperature sensor (turbo) connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 9.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO) |
Replace the intake air temperature sensor (turbo) (Click here).
|
| ||||
| 10.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Allow the engine to soak for 1 to 2 hours.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.
Read the value.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air and Intake Air Temp (Turbo).
Read the value.
| NEXT | ||
| ||