Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for DVD)

DTC    5C-40    Camera Picture Error

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
5C-40
Synchronous signal from camera cannot be transmitted..
  1. Harness or connector
  2. Television camera assembly
  3. Navigation receiver assembly

WIRING DIAGRAM


E182334E05


E182334E06


INSPECTION PROCEDURE

1.CHECK NAVIGATION RECEIVER ASSEMBLY


    E182335E01
  1. w/ "Bluetooth" Function:

    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E106-2 (CA+) - E106-12 (CGND)
      Ignition switch ON, shift lever in R
      5.8 to 6.2 V



    E138081E05
  1. w/o "Bluetooth" Function:

    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E54-24 (CA+) - E54-21 (CGND)
      Ignition switch ON, shift lever in R
      5.8 to 6.2 V



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


2.CHECK NAVIGATION RECEIVER ASSEMBLY (DISPLAY SIGNAL)


  1. w/ "Bluetooth" Function:


    E174002E05

    1. Using an oscilloscope, check the waveform.
      Measurement Condition 
      Item
      Content
      Tester Connection
      E106-1 (V+) - E106-11 (V-)
      Tool Setting
      0.2 V/DIV., 50 μs/DIV.
      Condition
      1. Ignition switch ON, shift lever in R*1
      2. Ignition switch ON, shift lever in R, screen is blacked out by covering camera lens*2

      OK:
      Waveform is as shown in illustration.



  1. w/o "Bluetooth" Function:


    E185171E01

    1. Using an oscilloscope, check the waveform.
      Measurement Condition 
      Item
      Content
      Tester Connection
      E54-22 (V+) - E54-23 (V-)
      Tool Setting
      0.2 V/DIV., 50 μs/DIV.
      Condition
      1. Ignition switch ON, shift lever in R*1
      2. Ignition switch ON, shift lever in R, screen is blacked out by covering camera lens*2

      OK:
      Waveform is as shown in illustration.



NG
Go to step 3
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - TELEVISION CAMERA)


    E182336E01
  1. w/ "Bluetooth" Function:

    1. Disconnect the E106 navigation receiver assembly connector.



    2. E182442E01
    3. Disconnect the S7 television camera assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E106-1 (V+) - S7-2 (CV+)
      Always
      Below 1 Ω
      E106-2 (CA+) - S7-4 (CB+)
      Always
      Below 1 Ω
      E106-11 (V-) - S7-1 (CV-)
      Always
      Below 1 Ω
      E106-12 (CGND) - S7-3 (CGND)
      Always
      Below 1 Ω
      E106-1 (V+) - Body ground
      Always
      10 kΩ or higher
      E106-2 (CA+) - Body ground
      Always
      10 kΩ or higher
      E106-11 (V-) - Body ground
      Always
      10 kΩ or higher
      E106-12 (CGND) - Body ground
      Always
      10 kΩ or higher



    E182692E02
  1. w/o "Bluetooth" Function:

    1. Disconnect the E54 navigation receiver assembly connector.



    2. E182442E01
    3. Disconnect the S7 television camera assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E54-22 (V+) - S7-2 (CV+)
      Always
      Below 1 Ω
      E54-24 (CA+) - S7-4 (CB+)
      Always
      Below 1 Ω
      E54-21 (CGND) - S7-3 (CGND)
      Always
      Below 1 Ω
      E54-23 (V-) - S7-1 (CV-)
      Always
      Below 1 Ω
      E54-22 (V+) - Body ground
      Always
      10 kΩ or higher
      E54-24 (CA+) - Body ground
      Always
      10 kΩ or higher
      E54-21 (CGND) - Body ground
      Always
      10 kΩ or higher
      E54-23 (V-) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TELEVISION CAMERA ASSEMBLY (Click here)